SEA 802.11p Add-On for LabVIEW - FULL API by S.E.A. Datentechnik GmbH Monitoring and RF Compliance of IEEE 802.11p Comm for V2X
| Starting at | $ 17,193 | (view pricing options) |
- Simulate dense traffic/stress 802.11p communication up to the theoretical limit of 802.11p
- Catch 802.11p messages for extended monitoring and testing (even invalid frames)
- Inject erroneous messages overriding MAC control and timing (even with corrupt frame content)
- Measure RF signals and validate and check for standard compliance all in parallel!
- Apply typical RF measurement and analysis methods; validate conformity to international standards
- For the full feature list, refer to the 802.11p MON and RFC API product pages
- Download
The SEA 802.11p Add-On for LabVIEW delivers unique access to the DSRC and ITS-G5 802.11p standards for future V2X (vehicle-to-anything) communication based on NI hardware. It consists of three separate parts: COMMS API, Monitoring API (MON), and RF-Compliance API (RFC). This product page covers the compilation of the MON and RFC, resulting in the FULL API.
The MON API overcomes the limits of chipset-based 802.11p communication. No Tx and Rx load limits, detailed failure injection, and deep monitoring are available for simulation, data and timing manipulation (Packet Replay), and monitoring (TZSP) of 802.11p data traffic.
The RFC API provides RF measurement and validation of the RF signal against ETSI, WAVE, and IEEE standards.
For further details on each API, refer to the product pages for the 802.11p MON and RFC APIs.
The COMMS API is required for operation and is automatically installed along with the other APIs if not yet installed.
Support Information
This product is supported by the third-party provider and not by NI. For more information, contact S.E.A. Datentechnik GmbH at:
English Website: www.sea-gmbh.com/en/v2x; German Website: www.sea-gmbh.com/v2x
Email: v2x@sea-gmbh.com
Disclaimer: This example package (this "program") was developed by a National Instruments ("NI") Engineer. Although provided by National Instruments, this program may not be completely tested and verified, and NI does not guarantee its quality in any way or that NI will continue to support this program with each new revision of related products and drivers. THIS PROGRAM IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND AND SUBJECT TO CERTAIN RESTRICTIONS AS MORE SPECIFICALLY SET FORTH IN NI.COM'S TERMS OF USE.
The MON API overcomes the limits of chipset-based 802.11p communication. No Tx and Rx load limits, detailed failure injection, and deep monitoring are available for simulation, data and timing manipulation (Packet Replay), and monitoring (TZSP) of 802.11p data traffic.
The RFC API provides RF measurement and validation of the RF signal against ETSI, WAVE, and IEEE standards.
For further details on each API, refer to the product pages for the 802.11p MON and RFC APIs.
The COMMS API is required for operation and is automatically installed along with the other APIs if not yet installed.
Support Information
This product is supported by the third-party provider and not by NI. For more information, contact S.E.A. Datentechnik GmbH at:
English Website: www.sea-gmbh.com/en/v2x; German Website: www.sea-gmbh.com/v2x
Email: v2x@sea-gmbh.com
Disclaimer: This example package (this "program") was developed by a National Instruments ("NI") Engineer. Although provided by National Instruments, this program may not be completely tested and verified, and NI does not guarantee its quality in any way or that NI will continue to support this program with each new revision of related products and drivers. THIS PROGRAM IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND AND SUBJECT TO CERTAIN RESTRICTIONS AS MORE SPECIFICALLY SET FORTH IN NI.COM'S TERMS OF USE.
|
Guarantee your price for 30 days (learn more) |
|
|
|