- 300 MHz bandwidth
- 2 GS/s maximum real-time, up to 20 GS/s equivalent-time sampling
- 2 simultaneously sampled channels
- Deep onboard memory - 8 MB/ch standard, up to 256 MB/ch
- 100 mV to 10 V input ranges
- 50 Ω and 1 MΩ input impedance
Data Sheet |
Configure System
The NI PXI-5152 high-speed digitizer features 300 MHz analog bandwidth and up to 2 GS/s real-time sample rate (20 GS/s equivalent-time sample rate for repetitive signals), making it ideal for acquisition and characterization of fast, nanosecond-edge speeds. The digitizer also comes equipped with up to 256 MB of memory per channel to provide high sustained sample rates over extended data capture windows.
The PXI-5152 is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries.
A digitizer optimized for automated test uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware - including arbitrary waveform generators, high-speed digital I/O, and other digitizers - so you can build and customize a complete mixed-signal or high-channel-count test system, up to 34 phase synchronous 1 GS/s channels in a single PXI chassis.
Additional Product Information
Specifications Documents
Specifications Summary
| General | |
| Form Factor | PXI |
| OS Support | Windows, Real-Time |
| Measurement Type | Voltage |
| Analog Input | |
| Number of Channels | 2 SE |
| Sample Rate | 2 GS/s/ch |
| Random Interleaved Sampling (RIS) Rate | 20 GS/s |
| Bandwidth | 300 MHz |
| Frequency Range | 0..300 MHz |
| Resolution | 8 bits |
| Simultaneous Sampling | Yes |
| Maximum On-Board Memory | 256 MB/ch |
| Maximum Voltage Measurement Range | -5..5 V |
| Range Sensitivity | 39 mV |
| Minimum Voltage Measurement Range | -50..50 mV |
| Range Sensitivity | 390 µV |
| Maximum Common Mode Voltage | 42 V |
| Input Impedance | 1 MOhm, 50 Ohm |
| Provides Digital Down Conversion? | No |
| Supports Alias Protected Decimation? | No |
| Integrated Signal Conditioning | Low-pass filtering |
| Analog Output | |
| Number of Channels | 0 |
| Digital I/O | |
| Number of Channels | 0 |
| Timing/Triggering/Synchronization | |
| Synchronization Bus (RTSI) | Yes |
| T-clock Capability | Yes |
| Triggering | Analog, Digital |
| External Clocking | Yes |
| Physical Specifications | |
| Length | 16 cm |
| Width | 10 cm |
| Height | 2 cm |
| I/O Connector | BNC connectors, SMB male |
Factory Installation
Reduce your setup time with National Instruments installation services and get a system you can use out of the box. Factory installation services include:
- Installation of all individual hardware and software components as well as full testing to eliminate conflicts
- Custom documentation plus a custom restore and startup utility
- 2-year warranty and calibration coverage
This service is only available for PXI, CompactRIO, and Compact FieldPoint systems.
Extended Warranties
National Instruments designs and manufactures all products to minimize failures, but we know unexpected failures can still occur. Extended warranties provide a fixed economical price at the time of system purchase covering any repair costs for up to three years.
- Significant cost savings compared to individual repair incidents
- Fault location, diagnostics, and repair by NI any time the system product fails
- All parts and labor costs covered as well as any adjustments needed to bring the hardware back to manufacturing specifications
Calibration
NI recognizes the need to maintain properly calibrated devices for high-accuracy measurements. We provide manual calibration procedures, services to recalibrate your products, and automated calibration software to calibrate many of our measurement products.
Training
NI training is the fastest, most certain route to productivity with NI tools and successful application development.
Repair Services
- You can return your registered product under warranty at no additional labor and parts cost. NI offers fault location, diagnostics, and repair any time the system fails as well as any adjustments needed to bring the hardware back to manufacturing specifications.
- Contact us to obtain a Return Material Authorization (RMA) form and shipping instructions
- View your RMA support request status online
- Register your product
Technical Support
www.ni.com/support
|