- 10 x1 (1-wire) multiplexer configuration
- Fully software-programmable
- 12 A switching/12 A carry
- Tight synchronization with instruments through hardware triggers
- 65 channels/s scanning speed
- 300 VDC/300 VAC
Data Sheet |
Configure System
View Diagram
Select one of the following options for product configuration and pricing:
Please select the country where you will use the product(s) so that we can provide you with accurate pricing, availability, and purchasing information
The National Instruments PXI-2585 is a high-power switch module in a single-slot, 3U PXI module. It is configured as a 10x1 multiplexer with both low contact resistance and high isolation voltage. The NI PXI-2585 is rated for high currents (up to 12 A) and high voltages (up to 300 VDC/300 VAC) and is ideal for switching power signals and loads in control applications and battery, power supply,and automotive testing.
Additional Product Information
Related Information
Specifications Documents
Specifications Summary
| General | |
| Form Factor | PXI |
| OS Support | Windows, Real-Time, Linux |
| LabVIEW RT Support | Yes |
| Switch Type | Multiplexer |
| Relay Type | Electromechanical |
| Connectivity | Back Shell Connector |
| Product Certifications | C-Tick, CAN/CSA, CE, FCC Part 15, IEC, UL - Product Safety |
| Input Characteristics | |
| Multiplexer Configurations | 10x1, 1-wire |
| Maximum Switching Voltage DC (Pollution Degree 2) | 300 VDC |
| Maximum Switching Voltage AC | 300 Vrms |
| Maximum Switching Current | 12 A |
| Maximum Carry Current | 12 A |
| Maximum Switching Power | 300 W |
| Bandwidth | 10 MHz |
| Relay Count Tracking | Yes |
| Voltage Category | CAT II |
| Path Resistance (Typical) | 50 mOhm |
| Dynamic Characteristics | |
| Mechanical Relay Life | 1 x 108 cycles |
| Scan Rate | 65 cycles/s |
| Timing/Triggering/Synchronization | |
| Synchronization Bus (RTSI) | Yes |
| Triggering | Digital |
| External Clocking | No |
| Physical Specifications | |
| Length | 16 cm |
| Width | 10 cm |
| Height | 2 cm |
| I/O Connector | 20-pin Positronic plug |
Factory Installation
Reduce your setup time with National Instruments installation services and get a system you can use out of the box. Factory installation services include:
- Installation of all individual hardware and software components as well as full testing to eliminate conflicts
- Custom documentation plus a custom restore and startup utility
- 2-year warranty and calibration coverage
This service is only available for PXI, CompactRIO, and Compact FieldPoint systems.
Extended Warranties
National Instruments designs and manufactures all products to minimize failures, but we know unexpected failures can still occur. Extended warranties provide a fixed economical price at the time of system purchase covering any repair costs for up to three years.
- Significant cost savings compared to individual repair incidents
- Fault location, diagnostics, and repair by NI any time the system product fails
- All parts and labor costs covered as well as any adjustments needed to bring the hardware back to manufacturing specifications
Calibration
NI recognizes the need to maintain properly calibrated devices for high-accuracy measurements. We provide manual calibration procedures, services to recalibrate your products, and automated calibration software to calibrate many of our measurement products.
Training
NI training is the fastest, most certain route to productivity with NI tools and successful application development.
Repair Services
- You can return your registered product under warranty at no additional labor and parts cost. NI offers fault location, diagnostics, and repair any time the system fails as well as any adjustments needed to bring the hardware back to manufacturing specifications.
- Contact us to obtain a Return Material Authorization (RMA) form and shipping instructions
- View your RMA support request status online
- Register your product
Technical Support
www.ni.com/support
|