- Scheduled for obsolescence. For new designs, NI recommends the PCI-6281.
- Two 12-bit analog outputs; 8 digital I/O lines; two
24-bit counters; analog triggering - Superior LabVIEW, LabWindows™/CVI, and Measurement Studio integration for VB and VS .NET
- Traditional NI-DAQ (Legacy) driver software included
- Free award-winning global services and support - ni.com/support
- NIST-traceable calibration certificate and more than 70 signal conditioning options
 Data Sheet
most popular item(s) |
National Instruments recommends NI M Series data acquisition (DAQ) hardware and NI-DAQmx driver software for new applications. Increase resolution 64 times, increase sampling, and improve your accuracy with the 18-bit, 625 kS/s NI PCI-6281 DAQ board.
Add sensor and high-voltage measurement capability to your E Series device with SCC or SCXI signal conditioning. The NI AT-MIO-16E-2 uses E Series technology to deliver high-performance, reliable data acquisition capabilities to meet a wide range of application requirements. You get up to 500 kS/s, 12-bit resolution with 16 single-ended analog inputs. Depending on your type of hard drive, this board can stream to disk at rates up to 500 kS/s.
The mark LabWindows is used under a license from Microsoft Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
Additional Product Information
Related Information
Specifications Documents
Specifications Summary
| General | |
|---|
| Form Factor | ISA |
|---|
| OS Support | Windows |
|---|
| DAQ Product Family | E Series |
|---|
| Analog Input | |
|---|
| Number of Channels | 16 SE/8 DI |
|---|
| Sample Rate | 500 kS/s |
|---|
| Resolution | 12 bits |
|---|
| Simultaneous Sampling | No |
|---|
| Maximum Voltage Range | -10..10 V |
|---|
| Range Accuracy | 14.369 mV |
|---|
| Minimum Voltage Range | -50..50 mV |
|---|
| Range Accuracy | 0.09 mV |
|---|
| Number of Ranges | 15 |
|---|
| On-Board Memory | 2048 samples |
|---|
| Analog Output | |
|---|
| Number of Channels | 2 |
|---|
| Update Rate | 1 MS/s |
|---|
| Resolution | 12 bits |
|---|
| Maximum Voltage Range | -10..10 V |
|---|
| Range Accuracy | 8.127 mV |
|---|
| Minimum Voltage Range | -10..10 V |
|---|
| Range Accuracy | 8.127 mV |
|---|
| Current Drive (Channel/Total) | 5 mA |
|---|
| Digital I/O | |
|---|
| Number of Channels | 8 DIO |
|---|
| Timing | Software |
|---|
| Logic Levels | TTL |
|---|
| Maximum Input Range | 0..5 V |
|---|
| Maximum Output Range | 0..5 V |
|---|
| Input Current Flow | Sinking, Sourcing |
|---|
| Programmable Input Filters | No |
|---|
| Output Current Flow | Sinking, Sourcing |
|---|
| Current Drive (Channel/Total) | 24 mA/192 mA |
|---|
| Watchdog Timer | No |
|---|
| Supports Programmable Power-Up States? | No |
|---|
| Supports Handshaking I/O? | No |
|---|
| Supports Pattern I/O? | No |
|---|
| Counter/Timers | |
|---|
| Number of Counter/Timers | 2 |
|---|
| Resolution | 24 bits |
|---|
| Maximum Source Frequency | 20 MHz |
|---|
| Minimum Input Pulse Width | 10 ns |
|---|
| Logic Levels | TTL |
|---|
| Maximum Range | 0..5 V |
|---|
| Timebase Stability | 100 ppm |
|---|
| GPS Synchronization | No |
|---|
| Pulse Generation | Yes |
|---|
| Buffered Operations | Yes |
|---|
| Debouncing/Glitch Removal | No |
|---|
| Number of DMA Channels | 1 |
|---|
| Timing/Triggering/Synchronization | |
|---|
| Synchronization Bus (RTSI) | Yes |
|---|
| Triggering | Analog, Digital |
|---|
| Physical Specifications | |
|---|
| Length | 33.8 cm |
|---|
| Width | 9.9 cm |
|---|
| I/O Connector | 68-pin male SCSI-II type |
|---|
Extended Warranties
National Instruments designs and manufactures all products to minimize failures, however unexpected failures can still occur. Extended warranties provide a fixed economical price at the time of system purchase, covering any repair costs for up to three years. In addition, they offer the following benefits:
- Significant cost savings compared to individual repair incidents
- Fault location, diagnostics, and repair by NI any time the system product fails
- All parts and labor costs covered as well as any adjustments needed to restore the hardware to manufacturing specifications
For more information about your warranty options:
Calibration
NI recognizes the need to maintain properly calibrated devices for high-accuracy measurements. NI provides manual calibration procedures, services to recalibrate your products, and automated calibration software to calibrate many NI measurement products.
Training
NI training is the fastest, most certain route to productivity with NI tools and successful application development.
Repair Services
Return your registered product under warranty at no additional labor and parts cost. NI offers fault location, diagnostics, and repair any time the system fails as well as any adjustments needed to restore the hardware to manufacturing specifications.
Technical Support
ni.com/support
|
