SCC-68 User Guide and Specifications
The SCC-68 is an I/O connector block for easy signal connection to a National Instruments M Series or E Series data acquisition (DAQ) device. This manual describes the SCC-68 and explains how to connect and use the connector block with National Instruments M Series or E Series DAQ devices. Edition Date: August-2006 URL: http://digital.ni.com/manuals.nsf/websearch/6ECC13E530315D21862571C3004FF365

SC-2345/2350 Carrier User Manual and Specifications
This document describes how to install and configure the SC-2345/2350 carrier. The SC-2345/2350 carrier transfers signals to and from 68-pin E/M Series data acquisition (DAQ) devices, referred to as the DAQ device in this manual. When used with SCC Series modules and a shielded 68-pin cable, the Edition Date: July-2006 URL: http://digital.ni.com/manuals.nsf/websearch/09FC2D464C3C38A1862571850066A88D

SCC-RTD01 Resistance Temperature Detector User Guide and Specifications
The SCC-RTD01 resistance temperature detector (RTD) input module accepts up to two RTD input signals from 2-, 3-, or 4-wire RTDs. Each module consists of two RTD input channels, a 30 HZ Butterworth lowpass filter for each channel and a 1 mA excitation current source. Each input channel includes an Edition Date: July-2006 URL: http://digital.ni.com/manuals.nsf/websearch/6D5CE73F4F8A6F668625718500661E0E

SCC-TC Series Thermocouple Input Modules User Guide and Specifications
The SCC-TC Series thermocouple input modules, SCC-TC01 and SCC-TC02, accept input signals from B-, E-, J-, K-, N-, R-, S-, and T-type thermocouples. Each module contains thermistor circuitry powered by 2.5 V, to compensate for cold-junction effects and can detect open thermocouple circuits. Each Edition Date: July-2006 URL: http://digital.ni.com/manuals.nsf/websearch/7FAF6A7D786879B38625718500657322

SCC-RLY01 Relay Module User Guide and Specifications
The SCC-RLY01 contains one single-pole double-throw (SPDT) nonlatching relay capable of switching 5 A at 30 VDC or 250 VAC when using an SCC-68. Any single E/M Series DAQ device digital input/output (P0.) line 0 to 7 can control the SCC-RLY01. Edition Date: May-2006 URL: http://digital.ni.com/manuals.nsf/websearch/1BECC1FA3A47A22D8625714F004E15A3

SCC-A10 Voltage Attenuator Module User Guide and Specifications
The SCC-A10 voltage attenuator module accepts up to two voltage sources of 60 V maximum amplitude and attenuates each voltage by a factor of 10. A differential instrumentation amplifier buffers each input signal. The SCC-A10 contains circuitry capable of protecting E/M Series DAQ devices for input Edition Date: December-2005 URL: http://digital.ni.com/manuals.nsf/websearch/91DE4E5D395AD2C4862570C90057CC85

SCC-AI Series Isolated Analog Input Modules User Guide and Specifications
The SCC-AI Series isolated analog input modules can extract a relatively low-amplitude input signal from a high-common-mode voltage so the E/M Series DAQ device can measure the input signal. They also can amplify and filter the input signal, resulting in higher measurement resolution and accuracy. Edition Date: December-2005 URL: http://digital.ni.com/manuals.nsf/websearch/EC8954C20F3FD057862570C900577D66

SCC-AO10 Isolated Analog Output Module User Guide and Specifications
The SCC-AO10 is an isolated voltage output module with an output range of 10 V. The output voltage level is controlled by the DAC output of an E/M Series DAQ device. You can increase the output voltage level to 20 V by connecting two SCC-AO10 modules in series. Edition Date: December-2005 URL: http://digital.ni.com/manuals.nsf/websearch/3C8768ADF63D98A6862570C900585591

SCC-CO20 Isolated Current Output Module User Guide and Specifications
The SCC-CO20 is an isolated current output module that outputs up to 20 mA. The output current level is proportional to the voltage applied to the module by an analog output channel of an E/M Series DAQ device. Edition Date: December-2005 URL: http://digital.ni.com/manuals.nsf/websearch/5053360E687A369B862570C9005823AF

SCC-CTR01 Isolated Counter/Timer I/O Module User Guide and Specifications
The SCC-CTR01 is a two input and one output isolation module for general-purpose counter/timers on DAQ devices. Edition Date: September-2005 URL: http://digital.ni.com/manuals.nsf/websearch/AAFC29EDEC595FF0862570690075F34C