|
SCC-AI Series Isolated Analog Input Modules User Guide and Specifications
The SCC-AI Series isolated analog input modules can extract a relatively low-amplitude input signal from a high-common-mode voltage so the E/M Series DAQ device can measure the input signal. They also can amplify and filter the input signal, resulting in higher measurement resolution and accuracy.
Edition Date:
August-2008
URL: http://digital.ni.com/manuals.nsf/websearch/E210C47A667D2C70862574B800671301
|
|
SCC-AO10 Isolated Analog Output Module User Guide and Specifications
The SCC-AO10 is an isolated voltage output module with an output range of 10 V. The output voltage level is controlled by the DAC output of an E/M Series DAQ device. You can increase the output voltage level to 20 V by connecting two SCC-AO10 modules in series.
Edition Date:
August-2008
URL: http://digital.ni.com/manuals.nsf/websearch/349F6B45EFD0500D862574B80063FB9D
|
|
SCC-CO20 Isolated Current Output Module User Guide and Specifications
The SCC-CO20 is an isolated current output module that outputs up to 20 mA. The output current level is proportional to the voltage applied to the module by an analog output channel of an E/M Series DAQ device.
Edition Date:
August-2008
URL: http://digital.ni.com/manuals.nsf/websearch/1BCC7DB52C38EED5862574B800660D19
|
|
SCC-RLY01 Relay Module User Guide and Specifications
The SCC-RLY01 contains one single-pole double-throw (SPDT) nonlatching relay capable of switching 5 A at 30 VDC or 250 VAC when using an SCC-68. Any single E/M Series DAQ device digital input/output (P0) line 0 to 7 can control the SCC-RLY01.
Edition Date:
August-2008
URL: http://digital.ni.com/manuals.nsf/websearch/AF0FF3DD35C246F1862574B800650EA0
|
|
Read Me First: Safety and Electromagnetic Compatibility
This document contains safety instructions and electromagnetic compatibility (EMC) information for the hardware it accompanies.
Edition Date:
February-2008
URL: http://digital.ni.com/manuals.nsf/websearch/36414F659C67A10B862573D7006BAEA7
|
|
はじめにお読みください: 安全対策と電磁両立性について
このドキュメントには、ハードウェアの安全対策および電磁両立性（EMC）に関する情報が記載されています。
Edition Date:
February-2008
URL: http://digital.ni.com/manuals.nsf/websearch/5E5967295810BAE1862573E9006F6884
|
|
SCC Quick Start Guide
This document explains how to install, configure, and set up National Instruments SCC modules. This document assumes you have already installed, configured, and tested the data acquisition (DAQ) device you will connect to the SC-2345/2350 carrier.
Edition Date:
January-2008
URL: http://digital.ni.com/manuals.nsf/websearch/28EB66698FFD7B218625736B006619A2
|
|
SCC-CTR01 Isolated Counter/Timer I/O Module User Guide and Specifications
The SCC-CTR01 is a two input and one output isolation module for general-purpose counter/timers on DAQ devices.
Edition Date:
December-2007
URL: http://digital.ni.com/manuals.nsf/websearch/CCA27C29960528BC8625738700573DD7
|
|
SC-2345/2350 Carrier User Manual and Specifications
This document describes how to install and configure the SC-2345/2350 carrier. The SC-2345/2350 carrier transfers signals to and from 68-pin E/M Series data acquisition (DAQ) devices. When used with SCC Series modules and a shielded 68-pin cable, the SC-2345/2350 carrier offers easy-to-use, rugged,
Edition Date:
July-2007
URL: http://digital.ni.com/manuals.nsf/websearch/977C8687049A4E7F8625730800636F9B
|
|
SCC-68 User Guide and Specifications
The SCC-68 is an I/O connector block for easy signal connection to a National Instruments M Series or E Series data acquisition (DAQ) device. This manual describes the SCC-68 and explains how to connect and use the connector block with National Instruments M Series or E Series DAQ devices.
Edition Date:
August-2006
URL: http://digital.ni.com/manuals.nsf/websearch/6ECC13E530315D21862571C3004FF365
|
