Academic Company Events NI Developer Zone Support Solutions Products & Services Contact NI MyNI
Manuals

Category(s) Selected [start over]

Edition
: 2004 [remove] ,
Product
: Signal Conditioning [remove] ,
11-20 de 22
Manuals [see results below]. To refine your results, select another category.
Product
SCXI (12)
SCC (8)
Sensors (2)
Document Type
User Manual (11)
Specifications (15)
Installation Guide (5)
Calibration Procedure (1)
Other (4)

Sort by:
11-20 de 22
|

NI PXI-1052 User Manual and Specifications
The NI PXI-1052 User Manual contains information about installing, configuring, using, and maintaining the NI PXI-1052 chassis. Edition Date: April-2004 URL: http://digital.ni.com/manuals.nsf/websearch/AD0403BA57F966AC86256E3F007A4014

NI SCXI-1160/1161 Jumpers Note to Users
This document discusses (1) the jumpers on the NI SCXI-1160/1161 that are dedicated for communication between the NI SCXI-1160/1161 and the controller, and (2) the jumpers that indicate to the module what type of controller is connected to its rear connector. Edition Date: April-2004 URL: http://digital.ni.com/manuals.nsf/websearch/3DDB27DEF6EED77E86256E890052A350

BNC-2096 Installation Guide and Specifications
The BNC-2096 is a 16-channel rack-mount adapter for reading IEEE P1451.4 Transducer Electronic Data Sheet (TEDS) information from Class I TEDS sensors. This installation guide describes how to connect the BNC-2096 in a measurement system. Edition Date: March-2004 URL: http://digital.ni.com/manuals.nsf/websearch/9019B288E1D2791686256E46006E99F8

SCC-ACC01 Accelerometer Input Module User Guide and Specifications
The SCC-ACC01 accelerometer (ACC) input module accepts an active accelerometer input signal, passes it through a 0.8 Hz highpass filter, amplifies it, and then passes it through a 19 kHz lowpass Bessel filter and an output buffer. The module has a fixed gain of 2, so the maximum input range is 5 V. Edition Date: March-2004 URL: http://digital.ni.com/manuals.nsf/websearch/3B9B5B8B58F9FF4D86256E550054789E

SCC-CI20 Current Input Module User Guide and Specifications
The SCC-CI20 converts current to voltage by passing it through a precision 249 [ohm] resistor and sending the resulting voltage to the E Series DAQ device as a 0 to +5 V signal. The SCC-CI20 accepts up to two current sources at a maximum of 20 mA. A differential instrumentation amplifier buffers Edition Date: March-2004 URL: http://digital.ni.com/manuals.nsf/websearch/4E8C4F1BBB2994DA86256E55005EE94C

SCC-DI01 Isolated Digital Input Module User Guide and Specifications
The SCC-DI01 is a single-channel, optically isolated digital input module that can sense AC and DC digital signals, including TTL, up to 30 VDC or 30 VAC. Edition Date: March-2004 URL: http://digital.ni.com/manuals.nsf/websearch/A1A2FBDF2901726F86256E5500009F26

SCC-DO01 Isolated Digital Output Module User Guide and Specifications
The SCC-DO01 is a single-channel, optically isolated digital output module. The output circuitry consists of a photomos relay and a load resistor. You can use the SCC-DO01 with a 5–24 VDC external voltage supply to switch external devices such as transistors and solid-state relays. Edition Date: March-2004 URL: http://digital.ni.com/manuals.nsf/websearch/CDB7544737A4872C86256E550000CF32

SCC-FT01 Feedthrough Module User Guide and Specifications
The SCC-FT01 is a feedthrough module that connects directly to the analog input (AI) and analog output (AO) channels of a data acquisition (DAQ) device. You can use the breadboard area of the SCC-FT01 to develop custom signal-conditioning circuitry that can connect to and condition any of the Edition Date: March-2004 URL: http://digital.ni.com/manuals.nsf/websearch/85A4B05DD099DA1286256E55005B8B77

SCC-FV01 Frequency Input Module User Guide and Specifications
The SCC-FV01 frequency input module is a frequency-to-voltage converter designed to measure signals from frequency-generating sensors and other periodic signal sources. The DC output voltage of the module is proportional to the input frequency. Edition Date: March-2004 URL: http://digital.ni.com/manuals.nsf/websearch/DB9B21FA1D74B62B86256E54007A734A

SCC-LP Series Lowpass Filter Modules User Guide and Specifications
The SCC-LP Series lowpass filter modules contain fourth-order Butterworth filter circuitry. They accept two differential input signals within a 10 V range. A differential amplifier attenuates each signal by a factor of two. The output of the amplifier passes through a fourth-order Butterworth Edition Date: March-2004 URL: http://digital.ni.com/manuals.nsf/websearch/19CDA6A48986219586256E550058BD2C

Sort by:
11-20 de 22
|