Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Can I Connect a Quadrature Encoder to an M Series Card Using the SCC-FT01? I am trying to connect an encoder with UP/DOWN control to my M Series card using an SCC-FT01 feedthrough module. The SCC-FT01 User Guide says that UP/DOWN controls are tied to the P0.6 and P0.7 lines for E-Series use. However, my M-Series card uses different pins. Can I use this URL: http://digital.ni.com/public.nsf/allkb/10F258E034638B17862570380063E635

How Do I Control the SCC-RLY01 with My DAQ Board? I have an SC-2345 carrier with a SCC-RLY01 installed in one of the DIO slots. How do I open and close the relay? URL: http://digital.ni.com/public.nsf/allkb/54267CD3C238301D862570380076AAB8

Voltage Level on SCC-SGxx Excitation Source Drops when a Second Strain Gage is Attached When I attach a second strain gage to the SCC-SGxx module, the excitation source drops in voltage. What can I do? URL: http://digital.ni.com/public.nsf/allkb/DAD885075F6C63C286256FFF00430471

How to Connect Signals to the SCC-FT01 ? In SCC-FT01 documentation, you can not find which screws are used for counter singals. URL: http://digital.ni.com/public.nsf/allkb/33956269663E065B86256FEB005194CD

I Am Not Getting Any Frequency Readings When Using the SCC-FV01. I am trying to use the SCC-FV01 to measure a frequency signal that goes anywhere from 0 to 10 Volts. When I test it in MAX, it doesn't seem to be working. URL: http://digital.ni.com/public.nsf/allkb/D52F25097F164E4C86256FCD006027C9

How Do the Module Slots on the SC-2345 Map to the Channels on the DAQ Cards? Whenever I configure my SC-2345 and add the SCC modules to the slots, the channel number that appears right next to the module doesn't match to the channel numbers appearing when configuring a Task for them. What are all these channel numbers and why are they different? URL: http://digital.ni.com/public.nsf/allkb/1D49E47CB61CE52486256F95001A740A

SCC-SG11シャントキャリブレーションモジュールはどのように使うものですか？ Measurement & Automation Explorer（MAX）でSCCシリーズの歪ゲージモジュール（SCC-SGxx）用のグローバルチャンネル作成するとき、オプションとしてキャリブレーション機能がありません。SCC-SG11モジュールはシャントキャリブレーションを行えますが、これを使用してSCC URL: http://digital.ni.com/public.nsf/allkb/562C868E2BE4ADAF86257028001F139A

Using the SCC-SG11 Shunt Calibration Module When I create a strain type global channel in MAX using a SCC-Series strain gage module, there's no option to perform calibration. How can I use the SCC-SG11 module to calibrate the SCC-SG0X or SCC-SG24 strain gage module? URL: http://digital.ni.com/public.nsf/allkb/C77748880274A56686256F89007A4E3E

Why Is the Test Panel for the SCC-FT01 Grayed Out in Measurement and Automation Explorer? I have an SC 2345 connected to a PCI-6023E card and I am trying to read data from a flowmeter through an SCC-FT01 module connected to channel J1. I went to Measurement and Automation Explorer (MAX) to test this SCC-FT01 module, but when I click on the channel with this module the Test Panels URL: http://digital.ni.com/public.nsf/allkb/48AC78CFF157E6A886256F4A006A0E79

Accelerometer Resonant Frequency Control Missing in DAQmx When setting up an accelerometer channel in Traditional NI-DAQ, I have the option to set the resonant frequency; however, when setting up an accelerometer channel in NI-DAQmx, that option is nowhere to be found. Is that option hidden somewhere, or does it simply not exist? If it doesn't URL: http://digital.ni.com/public.nsf/allkb/BE14EDB0C6B6D54986256F1C0071EB42