Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Using the SC-2345 in Measurement and Automation Explorer with Traditional DAQ? How do I configure and test the SC-2345 in Measurement and Automation Explorer (MAX) if I am using Traditional DAQ? URL: http://digital.ni.com/public.nsf/allkb/BB29BE4658861E4986256F0400617F4B

Wire/Pin Combinations for 9-pin D-Sub SCC Connector What is the correlation of wire color with pin number for the 9-pin D-Sub connectors? URL: http://digital.ni.com/public.nsf/allkb/964F3AE96C5263A786256ED70062A6FA

SCC-RLY01 はNI-DAQmxでサポートされていますか？ NI-DAQ 7.0 を使用し、2つのSCC-RLY01をSC-2345で設定を行おうとしましたが、ドロップダウンリストに表示されません。SCC-RLY01をDAQmxで使用することはできますか？ URL: http://digital.ni.com/public.nsf/allkb/AA5A1C0DFD11B90F8625700C0048F8B5

Support for SCC-RLY-01 with NI-DAQmx I have NI-DAQ 7.0 installed and am trying to configure my SC-2345 with two SCC-RLY01 modules, but they do not appear as options. Can I use the SCC-RLY01 with NI-DAQmx? URL: http://digital.ni.com/public.nsf/allkb/9F9522340F8B1A5586256E7C006608C4

What Does the Analog and Digital Power Requirement for SCC Modules Mean? The specifications for the SCC Signal Conditioning modules give a power requirement specification for Analog and Digital. What does this mean and how are these values used to calculate the total power required per carrier? URL: http://digital.ni.com/public.nsf/allkb/6C5F21F122D61C9586256E29006B62F1

Are All the SC-2345 Ground Lines Connected? I have an SCC-FT01 plugged into an SC-2345, and I am seeing a slight offset on my readings. I think it may be caused by grounding issues. Are all the grounds on a SC-2345 connected? URL: http://digital.ni.com/public.nsf/allkb/4804BB9C978629B986256DCC0065C7C8

SC-2345의 모든 Ground Line들은 연결되어 있습니까? 저는 SC-2345에 SCC-FT01을 연결해서 사용하고 있습니다. 그리고 저는 제 측정값에서 약간의 offset을 발견했습니다. 제가 생각하기에 이것은 Ground에 관련된 문제로 인하여 발생된 것 같습니다. SC-2345의 모든 Ground Line들은 연결되어 있습니까? URL: http://digital.ni.com/public.nsf/allkb/3F07FC3956972B1886256EA5000DD139

How Can I Create A Custom Excitation Voltage For My Signal Conditioning System? I have a transducer / sensor that needs a custom excitation (example +12 V) voltage. How can I create a custom excitation voltage using my SCXI-1180 or the SCC-FT01 module for my Signal Conditioning System? URL: http://digital.ni.com/public.nsf/allkb/858E7959505F7C1386256DA3007EB4B5

Setting Up the SCC-ACC01 in a Dual-Stage Configuration I have an SCC-ACC01 (formerly SCC-Integrated Circuit Piezoelectric01) and an SCC-LP0X lowpass filter module. I want to setup the SCC-ACC01 in a dual-stage configuration.When I try to configure the SC-2345 in Measurement & Automation Explorer (MAX) I get an error stating that the URL: http://digital.ni.com/public.nsf/allkb/64FAAD167FB8156A86256D7A006A864C

Are There Fuses on the SC-2345 or the SCC-Modules? Problem: Does the SC-2345 or any of the SCC modules have fuses? Solution: No, neither the SC-2345 or the SCC modules that go in the SC-2345 have any type of fuses. URL: http://digital.ni.com/public.nsf/allkb/A95E3461762EEDCB86256D4E005A3198