Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

What Are Flyback Diodes and Why Are They Used? I have an output SSR module and I was told that I need to use flyback diodes to protect the system. What are these diodes and why are they used? URL: http://digital.ni.com/public.nsf/allkb/336D3653F6B6387386256F36005BE09F

Accessories in Traditional NI-DAQ and NI-DAQmx NI Home 3 ratings: 4.33 out of 5 Rate this Document Accessories in Traditional NI-DAQ and NI-DAQmx Hardware: Multifunction DAQ (MIOConnector Blocks>>BNC-2080, Multifunction DAQ (MIOConnector Blocks>>BNC-2090, Multifunction DAQ (MIOConnector Blocks>>BNC-2110, Multifunction DAQ (MIOConnector URL: http://digital.ni.com/public.nsf/allkb/B50A1CA411D90EAD86256F1E0065FDC0

传统的NI-DAQ和NI-DAQmx可以使用的附件 传统的NI-DAQ和NI-DAQmx驱动支持哪些DAQ附件？ URL: http://digital.ni.com/public.nsf/allkb/47ED1176DCD817F98625738800262362

Can I Use my SC-2311 with an M-Series Device? Problem: Can I use the SC-2311 with an M-series device? Solution: Yes, the SC-2311 is pin-compatible with M-series devices, and therefore can be used in DAQmx with 5B and SSR modules. You cannot add the SC-2311 as an accessory in DAQmx, but this is not a requirement for using the modules. URL: http://digital.ni.com/public.nsf/allkb/6CDB32DAFD77D4AB86256F1D004DE97F

Can I Use my SC-2311 with an M-Series Device? Problem: Can I use the SC-2311 with an M-series device? Solution: Yes, the SC-2311 is pin-compatible with M-series devices, and therefore can be used in DAQmx with 5B and SSR modules. You cannot add the SC-2311 as an accessory in DAQmx, but this is not a requirement for using the modules. URL: http://digital.ni.com/public.nsf/allkb/C022935B4593113286257116005719B6

M시리즈 보드로 SC-2311을 사용할 수 있습니까? 문제점: M시리즈 보드로 SC-2311을 사용할 수 있습니까? 솔루션: SC-2311은 현재 트레디셔널 NI-DAQ드라이버만 지원이 됩니다. M시리즈 보드는 DAQmx드라이버만 지원이 됩니다. URL: http://digital.ni.com/public.nsf/allkb/AAF25C3CAB959FBD86256F43001D9C4E

E-Series Common Mode Voltage Limitations I am performing an analog acquisition using a National Instruments data acquisition board and it says that I can input up to 10 V differentially. Does this mean that I can connect 100 V on one lead and 110 V on another lead? URL: http://digital.ni.com/public.nsf/allkb/1A9FB36240EAB28286256F1800063138

E-series Common Mode 최대전압 National Instrument의 데이터 수집 보드를 이용하여 아나로그 신호를 받고 있는데 differential 로 10V 까지 받을 수 있다고 나와있습니다. 그럼 제가 한 쪽에 100V 또 다른한 쪽에 110V를 연결해도 된다는 뜻입니까? URL: http://digital.ni.com/public.nsf/allkb/97CB0884F2507F6686256F4900437DA5

Configuring SC-2311 in MAX Problem: How can I configure my SC-2311 in MAX? Solution: If you want to configure SC-2311 using MAX you should be able to do it under Traditional NI-DAQ Devices. 1. Right click on the device under Traditional NI-DAQ Devices and go to Properties. 2. You will have a configuration window pop up 3. URL: http://digital.ni.com/public.nsf/allkb/CD1E01FA5FF7385586256F0F0059EE56

Why Does My RLY-01 SCC Module Default to the Normally Open (NO) State? Problem: Why Does My RLY-01 SCC Module Default to the Normally Open (NO) State? Solution: The RLY-01 module is driven by the DIO lines on Multifunction DAQ boards. The state of the RLY-01 module is not guaranteed until the board's DIO lines are in output mode. URL: http://digital.ni.com/public.nsf/allkb/C9D0249BF68667EA86256ED6004F2FCC