Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Why Can't SSR Output Modules Be Used with Certain DAQ Devices? A note on the SSR modules page in the National Instruments (NI) Catalog states:'The output modules (SSR-OAC-5, SSR-OAC-5A, and SSR-ODC-5) will not work with 6503 (DIO-24), 6508 (DIO-96), 1200 family, DAQCard-700, PC-LPM-16, AO-2DC family, or the extended digital I/O lines of E Series URL: http://digital.ni.com/public.nsf/allkb/3F33283974B3692786256894006D7953

External Power Supply with PB8H SSR Backplane Causes LEDs to be Half-Lit When Computer is Off The PB8H (70RCK8) SSR backplane shows the current state of the DAQ board's digital lines. When the board is connected to the computer's 5 V line, the LEDs turn off when the computer turns off. But when an external power supply is connected, they are half-lit when the computer is off, and then work URL: http://digital.ni.com/public.nsf/allkb/B9167581BECC955E862566DD0077D55B

Do SSR-OAC-5A Relays Work with Legacy Multifunction Input/Output (MIO) DAQ Boards? Can I use SSR-OAC-5A relay modules with legacy boards such as the AT-MIO-16L-9 or AT-MIO-16X? URL: http://digital.ni.com/public.nsf/allkb/862567530005F09C862566D40079EDDB

Cabling Solutions for the AT-DIO-32HS or PCI-DIO-32HS to the SSR Backplanes I want to have a 6 meter cable solution to my SSR backplane. I want a minimum of 16 channels. How can I do this? URL: http://digital.ni.com/public.nsf/allkb/B77EDB0B35DECB438625662C005A4BF4

Where Can I Find Documentation on the SSR Backplanes? Problem: Where can I find documentation on the SSR backplanes? Solution: The SSR backplanes are from Grayhill. You can find documentation about the Grayhill backplanes on their website at http://www.grayhill.com/. Information about the backplanes can be found under the section titled "System 50. URL: http://digital.ni.com/public.nsf/allkb/D53208AB0C3CA2B7862565DE00590030

How to Drive High Current Digital Devices I need to drive high current and voltage loads, such as motors, with my DIO board. The circuitry used on my boards does not drive enough current nor can they handle high switching voltages necessary for these devices. What can I do? URL: http://digital.ni.com/public.nsf/allkb/52CCD6F8B6B3127F862562A80083A5FC

如何驱动高电流的数字设备？ 我要用我得DIO板驱动高电流高电压的负载，例如引擎。板上的电路并不能驱动足够的电流或是承受高交变电压，我该怎么办？ URL: http://digital.ni.com/public.nsf/allkb/4F9DBA8ABA26386A86256D5D0031B6E7

電流の大きい素子の駆動方法 DIOボードを使用して、モータのような電圧・電流の大きい負荷を駆動する必要があります。しかし、DIOボードの回路では電流が足りず，必要なだけの高電圧をスイッチングさせることができません。どうすればよいでしょうか。 URL: http://digital.ni.com/public.nsf/allkb/090AD659E4D1D67586256F570029F0BE

고전류의 디지털 장비들은 어떻게 사용할 수 있습니까? 모터와 같은 고전류와 전압이 실리는 장비를 DIO 보드와 함께 사용하려고 합니다. 보드에 사용되는 회로는 충분한 전류를 보낼수 없을 뿐만 아니라 이러한 장비를 사용하는데 필요한 고전압의 스위칭을 다루지도 못합니다. 어떻게 사용할 수 있습니까? URL: http://digital.ni.com/public.nsf/allkb/A31592D0992A090886256E7F0020AECF

SSR Series AC Output Modules Will Not Work Properly with Boards that Have the 8255 Digital Chip My SSR series AC output modules are not turning on and off properly. I am controlling the module with a PC-DIO-24 DAQ card. URL: http://digital.ni.com/public.nsf/allkb/9AE7B889B2D3546F86256E8E00245679