Accessing General Purpose Digital I/O Lines of NuDrive with Motion Controller Board
I would like to be able to use the eight general purpose digital i/o lines available on my NuDrive motor drive. How can I access those lines?
URL: http://digital.ni.com/public.nsf/allkb/4D8548DF93CC698486256F030059608B
|
Current Per Phase and Current Per Axis Specifications
I currently own a stepper motor that specifies a maximum current per phase of 1.2 amps. I was looking at the possibility of using the National Instruments MID-7604 as an amplifier for this motor, but I noticed that this amplifier outputs a maximum current per axis of 1.4 amps. Is this going to work
URL: http://digital.ni.com/public.nsf/allkb/EFF68322CF8D0F2486256E9400805559
|
Relation Between Maximum Voltage Spec and Power Amplifier (Drive) Voltage Spec
I own a motor that has specifications for a maximum allowable voltage that is considerably less than the rating for all of the corresponding National Instruments drives. Does this mean I need another amplifier?
URL: http://digital.ni.com/public.nsf/allkb/17049AE00902FAC986256E590069B12F
|
My Motor Spins at Full Torque Until it Trips a Following Error When I Command it to Move
When I call the Initialize function from Measurement & Automation Explorer (MAX), or click the Start button in the Interactive Window, or when I try tuning my servo using Step Response inside MAX, or execute any other action that tries to move my motor, it runs at full speed and then stops
URL: http://digital.ni.com/public.nsf/allkb/D2F1EF10A39A549B86256DB20081C879
|
How to Connect NI 73xx Digital Outputs to Third Party Equipment
When I connect digital outputs from the NI 73xx controllers through a Universal Motion Interface (UMI) in order to move a motor, disable a drive or trigger an event, the signal at the motion controller will change; however, my third party drive will not generate any of these actions. Why is
URL: http://digital.ni.com/public.nsf/allkb/4654434B4A35B90A86256D9700646E02
|
我該如何連結 NI 73xx 數位觸發訊號與控制訊號輸出至他家協力廠商所提供的設備
有時，當我要連接數位訊號從 NI 734x 輸出至 UMI (Universal Motion Interface ) 以使馬達轉動、停止驅動器、或是觸發一個事件時，馬達控制卡上的訊號有改變，但是協力廠商的驅動器並沒有相對的輸出，是什麼原因造成這樣的情況？
URL: http://digital.ni.com/public.nsf/allkb/3D5AEE692482AA22862573C5003D0A70
|
Limit Switches Do Not Work Correctly With NI-Motion Hardware
After configuring my National Instruments motion controller card and my National Instruments Drive, my limit switches do not work correctly. The home switch on Axis 1 does not ever change state, and all of the limits on Axis 2 do not seem to work at all.
URL: http://digital.ni.com/public.nsf/allkb/7BE874EEE68EC5E986256D560064AEBF
|
極限開關無法與NI-Motion硬體正常作動?
當我設定National Instruments運動控制卡及驅動器後,我的極限開關作動不正常?軸一Home點開關狀態不會改變,且軸二所有極限開關動作不正常?
URL: http://digital.ni.com/public.nsf/allkb/2B6606DDA5B4C06286256D5D0013CD84
|
Can I Connect a 6-wire Unipolar Stepper Motor to the MID-7602/7604?
I have a unipolar motor and would like to use a MID-760x to drive it. The user manual says I cannot use 5 lead unipolar stepper motors, but I have a 4 phase (6 lead) unipolar stepper motor. Can I use the MID-760x?
URL: http://digital.ni.com/public.nsf/allkb/8B3FE54DBD307D2D86256D50006EC6DC
|
MID-7602/7604에 6라인 단극 스텦퍼 모터를 연결할 수 있습니까?
저는 단극 모터를 MID-760x를 이용하여 구동하고자 합니다. 매뉴얼에는 5라인 단극 스텦퍼 모터를 사용할 수 없다고 하는데, 제가 사용하고자 하는 것은 4상(6라인) 단극 스텦퍼 모터입니다. MID-760x를 이용할 수 있나요?
URL: http://digital.ni.com/public.nsf/allkb/ADA7CBE09176247586256D5D0004E29A
|
