Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

当把NI 9505模块插入一个上电的cRIO机箱中时，模块上指示机箱电源的LED灯没有亮？ 我的cRIO机箱已经上电并且工作正常，但是NI9505模块上的绿色的指示电源的LED灯没有亮。虽然 NI 9505 Operating Instructions上说..."当把NI 9505模块插入到一个上电的机箱中时，绿色的能源LED指示灯会发亮。" URL: http://digital.ni.com/public.nsf/allkb/52D8B28393C836F6862573C5003BB019

转矩模式和速度速度模式的区别以及NI-Motion对这两种模式的兼容性 我对第三方驱动器上的电流模式和速度模式的区别不是很了解，NI-7344兼容这两种模式么？ URL: http://digital.ni.com/public.nsf/allkb/BBFA491AB63E6044482572240035FD8A

哪些电机可以同MID-76xx驱动器工作 我正在为我的MID-76xx驱动器选择电机。所选的电机需要满足哪些规范？ URL: http://digital.ni.com/public.nsf/allkb/6228465F9A1839154825715F00353CE5

5-Phase Stepper Motor With An MID-760X Can A 5-Phase Stepper Motor or 5-Lead unipolar stepper motor be used with an MID-7602/7604? URL: http://digital.ni.com/public.nsf/allkb/08030C9A3994BF918625715D00089F9C

MID-760xに接続できるステッピングモータ ５線式（５ワイヤ）の２相ステッピングモータをMID-760xに接続しようと思っていますが、マニュアルに該当する接続方法の図がありません。５線式の２相ステッピングモータは接続できないのですか？MID-760xに接続できるステッピングモータはどのような形■> URL: http://digital.ni.com/public.nsf/allkb/8BCB4888A9453674862570FC001E79BB

Using the MID-765x Drive with Low Inductance Motors I have a motor with an inductance of less than 110 μH (microhenries). I would like to connect it to a MID-765x Drive. Is this possible? URL: http://digital.ni.com/public.nsf/allkb/2EAA91CB371582C38625708C005B7C00

What Motors will Work with the MID-76xx Drives? I am selecting motors for my MID-76xx Drive. What are the specifications the motor needs to meet? URL: http://digital.ni.com/public.nsf/allkb/421DCBF37C8334288625708C0073086B

Generating a Move Results in Axis Vibration When I send a move to my motor, the axis seems to vibrate in place, but it does not move. I have tried a variety of move distances, velocities, and accelerations, but the motor still doesn’t seem to ever move out of its initial position. What is causing this behavior? URL: http://digital.ni.com/public.nsf/allkb/883E53D872CC87B286256F33006D45F1

Accessing General Purpose Digital I/O Lines of NuDrive with Motion Controller Board I would like to be able to use the eight general purpose digital i/o lines available on my NuDrive motor drive. How can I access those lines? URL: http://digital.ni.com/public.nsf/allkb/4D8548DF93CC698486256F030059608B

Current Per Phase and Current Per Axis Specifications I currently own a stepper motor that specifies a maximum current per phase of 1.2 amps. I was looking at the possibility of using the National Instruments MID-7604 as an amplifier for this motor, but I noticed that this amplifier outputs a maximum current per axis of 1.4 amps. Is this going to work URL: http://digital.ni.com/public.nsf/allkb/EFF68322CF8D0F2486256E9400805559