Configuring the P7000 Series Stepper Drives for the Correct Motor
I have a P7000 Series Stepper Drive, and need to configure the drive for my specific motor. The sticker on the drive lists the appropriate switch settings to use for various motors, but mine is not listed. How can I configure the drive with the appropriate settings?
URL: http://digital.ni.com/public.nsf/allkb/43E49533369E4230862574130065CBF1
|
How Do I Access the DPull Pin on My UMI-7774?
I have a NI 733x, 734x, or 735x Motion Controller connected the the UMI-7774, and I need to change the default power-up state. I know that I need to either connect the DPull pin to ground or to 5V, depending on the state that I want to set, but I do not see any way to access that pin from
URL: http://digital.ni.com/public.nsf/allkb/DFD48E6863AD245A86257378007F1708
|
UMI-7774を使用してDPULLピンにアクセスすることはできますか
NI 733Ｘ， 734Ｘ， 735Ｘシリーズのモーションボードに、UMI-7774を接続していますが、ボードのデフォルトの起動時状態を変更する必要があります。起動時状態を設定するには、DPULLピンをセットしたい状態によって、グラウンドまた５Vに接続する必要がある
URL: http://digital.ni.com/public.nsf/allkb/C27008789FEB424586257386003408B3
|
我要如何存取UMI-7774上的DPull接腳?
我有NI 733x, 734x或735x系列的運動控制器和UMI-7774連結，同時我需要去改變預設的power-up狀態。根據我所要設定的狀態，我知道我需要將DPull接腳連結至ground或者是5V，但是我找不到方法去連結UMI-7774中的這支接腳。我要如何連結呢?
URL: http://digital.ni.com/public.nsf/allkb/797586B2F89D75898625740C0007B850
|
Where can I find the Danaher P7000AC (P70360) and P7000DC (P70530) Stepper Drive Manuals?
Where can I find the Danaher P7000AC (P70360) and P7000DC (P70530) Stepper Drive Manuals?
URL: http://digital.ni.com/public.nsf/allkb/FEB445A71B94412A86257345004DC76C
|
National Instruments Motion Controller Boards & Drivers
I have a National Instruments Motion Controller board but I am unsure if I should use ValueMotion, FlexMotion or NI-Motion. Which one should I use and why?
URL: http://digital.ni.com/public.nsf/allkb/782E7400A9FE22A68625731C005C973A
|
Conversion Factor on the NI 9505
The NI 9505 is a Servo Drive module that can be used for current loop control algorithms. These algorithms require the user to specify the Current Setpoint and Current Limit (Amps) as floating point [DBL] numbers. Because the FPGA on the NI 9505 does not currently interpret
URL: http://digital.ni.com/public.nsf/allkb/0E95A86A1323EBD38625729E000BD4A1
|
NI 9505上的转换因数
NI9505是一块伺服驱动模块，可以用在电流控制算法回路中。在这些算法中，需要用户以浮点数的形式（DBL）指定电流的Setpoint和极限值(以安培为单位)。由于与NI 9505一起工作的FPGA目前还不能支持浮点运算，所有，所有的浮点数都必须被转换成整数。■>
URL: http://digital.ni.com/public.nsf/allkb/BAACFF6AA68E4037862573C5003A88BD
|
Configuring Axis Resources for a Motion Dual-Loop Feedback System
I would like to use dual encoders, but I only have two axes on my MID. Measurement & Automation Explorer (MAX) defaults dual encoding to Axis 1 and 3, but I need to figure my second feedback encoder to a different axis on my UMI. Is this possible?
URL: http://digital.ni.com/public.nsf/allkb/57980429F24F87058625727D0003384F
|
NI 9505 Module Chassis Power LED is not Illuminated when Plugged into a Powered cRIO Chassis
My cRIO chassis is powered up and working properly, but the green power LED is not on, even though the NI 9505 Operating Instructions say... 'The Power LED (green) illuminates when the NI 9505 is properly inserted into a
URL: http://digital.ni.com/public.nsf/allkb/45E16F3A9F1A25508625727A007E5679
|
