Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Can I use the NI 9505 module to read from an encoder without a motor connected? I am developing a motion control application using the NI 9505 motion control module and would like to read from an encoder without a motor connected. I am certain that my encoder is working and connected properly but I can’t seem to read from the encoder using shipping examples. I also notice that URL: http://digital.ni.com/public.nsf/allkb/1915D2D7A3ED7996862575D80054D85E

¿Puedo Utilizar el Módulo NI 9505 para Leer de un Encoder Sin Tener un Motor Conectado? Estoy desarrollando una aplicación de control de movimiento utilizando el módulo NI 9505 y me gustaría leer de un encoder sin tener un motor conectado. Estoy seguro que mi encoder está funcionando y conectado correctamente pero al parecer no puedo leer del encoder utilizando los ejemplos incluidos. URL: http://digital.ni.com/public.nsf/allkb/49BB4492422BFD52862575E70052E174

Why does my Run/Stop bit not appear active while my motor is running? When using the Read per Axis Status VI, I am seeing the Run/Stop bit on my motor not turn true while the motor is running. How can I adjust my settings to generate this behavior? URL: http://digital.ni.com/public.nsf/allkb/797B98CAEF33FD25862575BA0068DE0E

Error -70072 con Controladores NI-Motion Cuando estoy usando mi controlador de Motion para generar una salida analógica con Load DAC.flx recibo el siguiente error: Error -70072: The Flexmotion controller is in power up reset state. Please execute the Clear Power Up Status function or VI before sending any commands to the controller ¿Cómo URL: http://digital.ni.com/public.nsf/allkb/8487B936D304B03E862575A0007E258D

Error -70072 with NI-Motion Controllers When using my motion controller to generate an analog output with Load DAC.flx, I receive Error -70072: The Flexmotion controller is in power up reset state. Please execute the Clear Power Up Status function or VI before sending any commands to the controller. How do I correct this error? URL: http://digital.ni.com/public.nsf/allkb/80CE15BEF4119134862575980051D4D6

How Can I Use the Trigger Inputs On My Motion Controller as General Purpose DIO? I read in the NI-Motion help that it is possible to use the High Speed Capture inputs on my motion controller as general purpose DIO. How do I configure my VI to do this? URL: http://digital.ni.com/public.nsf/allkb/52D4FAFA7B525D928625756800011D00

如何将我的运动控制器上的触发输入作为通用DIO使用？ 在阅读NI-Motion帮助后得知，我的运动控制器上的高速捕获输入(High Speed Capture inputs)能作为通用DIO使用。为了实现该功能，我该如何配置我的VI？ URL: http://digital.ni.com/public.nsf/allkb/83CEE5080FF465738625758A00321104

Can I Use a Motion Cable With a M-Series DAQ Card? I have a M-Series DAQ card and I want to connect it to a device that has a VHDCI connector. All the available DAQ cables have the VHDCI connector on only one end. But there is a Motion cable (SH68-C68-S) that has a VHDCI connector on both ends. Can I use the Motion Cable with my M-Series card? URL: http://digital.ni.com/public.nsf/allkb/A4D3C38C55B51229862575590063016C

Error -70119: The Desired Move Cannot be Completed When my axis tries to make a move I receive Error -70119 (NIMC_limitSwitchActiveError) The desired move cannot be completed because the limit input is active in the direction of travel. URL: http://digital.ni.com/public.nsf/allkb/A87BFBD6800860838625752100702EAF

Is it Possible to Read a Non-Quadrature Encoder with an NI Motion Controller? Is it possible to use the encoder inputs on my NI motion controller to read pulses from a non-quadrature encoder? URL: http://digital.ni.com/public.nsf/allkb/16E0C2CBFD218EF8862574BE006F451C