Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

What Gauge Wire Should be Used With the NI ELVIS? I am using the NI ELVIS, but do not know what size wire to use. What gauge wire does National Instruments recommend for use with the NI ELVIS? URL: http://digital.ni.com/public.nsf/allkb/B8524E1F1302F5D18625723E0058FC5D

SH68-68-D1などのケーブルに使われているコネクタのネジの規格 68Pinコネクタがついているデータ集録用ボードと接続する自作の端子台を作ろうと思っています。コネクタはSCSI用の68Pinでオスのコネクタというのは分かるのですが、固定するためのネジの規格がわかりません。SH68-68-D1などのケーブルに使われているコネクタ URL: http://digital.ni.com/public.nsf/allkb/37702BBB49987A96862572330005DC23

What SCC Modules are Supported by the SCC-68? Does the SCC-68 support every available National Instruments SCC module? URL: http://digital.ni.com/public.nsf/allkb/4592E570D078320886257211000C7CF0

Device Terminals on an Unlabled Connector Block I have a BNC-2111 with a PCI-6251 DAQ card. I would like to count the pulses of an external signal but PFI3 and PFI8 are not accessible. How do I access signals that do not appear to be available on the connector block such as Counter URL: http://digital.ni.com/public.nsf/allkb/CF01608CED56BF73862572060062717E

Where is Pin 14 on the SCC-68? If I look on the pin out for the SCC-68, there are 82 numbered screw terminals, but there is a Pin 83. According to the pin numbering on the SCC-68 and in the SCC-68 user manual, there is no Pin 14. Is this correct? URL: http://digital.ni.com/public.nsf/allkb/9107BF6D7ADBE46E862571FB005AAF59

Inaccurate Readings Performing Three-Wire Current-Voltage Measurements with NI-ELVIS Why do I see discontinuities or inaccurate measurements when performing a Three-Wire Current-Voltage Analysis of a transistor with NI-ELVIS? URL: http://digital.ni.com/public.nsf/allkb/97DEDBC623A90770862571F40063A772

My NI SCC-68 Does Not Appear in NI-DAQmx Devices in MAX Refer to the NI-DAQmx Readme for a list of supported devices. I have an NI SCC-68 that I want to configure in Measurement & Automation Explorer (MAX) with NI-DAQmx 8.0. When I attempt to add the NI SCC-68 as a new NI-DAQmx device, it is not available, but the NI SCC-2345 and and the URL: http://digital.ni.com/public.nsf/allkb/16B42C3FD44090D4862571BC0069422B

Can I Use a BNC-2090 and an SCXI Chassis on the Same DAQ Card? I currently have a system built with a BNC-2090 connected to my DAQ card. I'm adding the capability now to read in just a few thermocouples and I have an SCXI chassis and an 1102 lying around. Can I use my BNC-2090 to get my basic analog inputs and use my SCXI 1102 for my thermocouples while still URL: http://digital.ni.com/public.nsf/allkb/FDE04C8A1E4481B486257199005D71A7

我应该如何将SCB-68上冷端补偿和我的DAQPad-4350结合起来使用呢？ 我使用SCB-68和DAQPad-4350来测量热电偶。SCB-68没有作为附件在MAX中的设备列表中出现，所以是否表示无法把一个冷端补偿传感器和热电偶通道相连呢？ URL: http://digital.ni.com/public.nsf/allkb/02A642D4966DA8384825717600242726

我如何同步我cRIO-9002/9004 RT 控制器所有的时基，并使能我cRIO-9002/9004 RT 控制器的微秒定时循环？ 您必须修改远端目标 ni-rt.ini 文件以实现cRIO-9002/9004 RT控制器上所有时基的同步 URL: http://digital.ni.com/public.nsf/allkb/75EEC7EDDF4CBD7E482571750028017D