Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

How Can I Distribute a LabVIEW Application that Uses the NI-435X Driver? I have built a LabVIEW VI that interfaces with the NI-435X driver. I would now like to distribute my VI as an application. However, I do not see the NI-435X driver in the Additional Installers when I try to build my installer. How can I distribute this application? URL: http://digital.ni.com/public.nsf/allkb/0FD958CBC0BB2840862575DF007BF900

Calibration and IEPE Sensors Sold Through National Instruments Problem: How often should I calibrate IEPE sensors? Solution: Routine calibration of sensors and data acquisition equipment is recommended to maintain measurement quality. URL: http://digital.ni.com/public.nsf/allkb/B4EA7D7C135BE609862575D90069266D

Resource Library For IEPE Sensors Sold Through National Instruments This resource library is for any user who is integrating both NI DSA hardware and IEPE sensors, especially PCB sensors sold through ni.com.While National Instruments can facilitate the RMA (repair) process for any IEPE sensor sold through ni.com, the turnaround time is much longer than if you go URL: http://digital.ni.com/public.nsf/allkb/DA04F16F96CC5716862575D90072D650

Why Doesn't My NI-407x DMM Respond to Input Triggers? I'm trying to trigger my NI-407x Digital Multimeter, but the trigger either incrementally or never registers in hardware. What do I need to do to guarantee the NI-407x DMM triggers? URL: http://digital.ni.com/public.nsf/allkb/82DDD3B4E48351B6862575D900723094

Why Does My AudioMASTER Installation Run Slowly? When I try to install certain versions of AudioMASTER, the installation runs very slowly. The CPU load is constantly close to 100%. URL: http://digital.ni.com/public.nsf/allkb/0399C1B89DF791D9862575CC007A6A1E

Where can I find out what products need calibrating? I have a National Instruments device and need to know whether I need to calibrate it or not. Where can I find this information? URL: http://digital.ni.com/public.nsf/allkb/05DCF4B44AC68BEB862575CB00499A4B

Finite Generation with RFSG Results in Multiple Instances of Waveform I am using NI-RFSG and scripting to perform a finite generation with my Vector Signal Generator. The Resample and Write VI is used to write my waveform to the arbitrary Waveform generator. The generation is working correctly except that my waveform is being generated multiple times before URL: http://digital.ni.com/public.nsf/allkb/D6B2EC043C5E98F3862575CB000081F8

How to Monitor Device Temperature for the PXIe-5663 I would like to monitor the device temperature of my PXIe-5663 automatically in my program. How can I do this? URL: http://digital.ni.com/public.nsf/allkb/C2A9832717FD9BD8862575B300439809

Error -1074135028 When Closing Session to NI 5102 I am using an NI 5102 digitizer with the NI-SCOPE 3.5.1 driver. Whenever I stop my program using the niScope Close VI, I receive an error -1074135028, as seen below. What is causing this error and how can I fix it? URL: http://digital.ni.com/public.nsf/allkb/16CFFA1EADEB7D99862575AE007B0EA1

Seeing Steps in The Current Measurement On My I-V Graph I am using a Source Measure Unit (SMU) to perform a voltage sweep by programmatically incrementing the voltage output value. I am also using a NI PXI Digital Multimeter (DMM) to measure the current going through my unit under test. Why am I seeing steps in my I-V graph when it should be a smooth URL: http://digital.ni.com/public.nsf/allkb/AD37913A72B8D718862575AD005B731E