Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Using a GPIB PMC Card With a cPCI Bus Is it possible to use the National Instruments PMC GPIB card on a system with a cPCI bus form factor? I want to use this setup because of the smaller form factor of the cPCI bus. URL: http://digital.ni.com/public.nsf/allkb/BDBF2E81013F189C8625742C003A0B5B

LabVIEW and NI-488.2 Version Compatibility What versions of LabVIEW are compatible with different versions of the NI-488.2 driver? URL: http://digital.ni.com/public.nsf/allkb/2BFCEE471BECB95F862574020059117E

What is the Difference Between the GPIB 120A and GPIB 120B in Terms of Isolation? What is the main difference between the GPIB 120A and the GPIB 120B in terms of isolation? URL: http://digital.ni.com/public.nsf/allkb/41A4CB6D2874E12A862573ED003443D3

以隔離的角度來看，GPIB 120A 與 GPIB 120B 有什麼不同？ 以隔離的角度來看，GPIB 120A 與 GPIB 120B 有什麼主要的不同？ URL: http://digital.ni.com/public.nsf/allkb/A86DA1984F172CD08625743D000AE4DE

GPIBボードの設定に関して、デバイステンプレートのデバイス名変更を行なうにはどうしたらよいのでしょうか。 NI488.2 Version 2.5を使用しています。以前はVersion 1.70を使用していました。以前の様にConfiguration Utility からデバイステンプレートのデバイス名変更を行なおうと思いましたがそのような項目が見つかりません。どこからこの設定を行うことができるのでし URL: http://digital.ni.com/public.nsf/allkb/7A57DE2D807BD544862573DE004A985A

Getting started with the NI GPIB-485CT-A in serial mode I have configured my NI GPIB-485CT-A in serial mode. I have connected a GPIB device but am unable to communicate with this GPIB device. Can you please help? URL: http://digital.ni.com/public.nsf/allkb/E240FF1B748399D38625734B00272FB0

How to Configure NI Instrument Simulator for GPIB or Serial communication How do I configure the dip switches on my NI Instrument Simulator for the communication interface desired? URL: http://digital.ni.com/public.nsf/allkb/F0C979E8890C06C28625734100183BC9

TestStand シーケンスから VISA ステップをコールする方法 TestStand シーケンスから VISA ステップをコールして、計測器を制御したいです。どのように構築すると再利用しやすいステップをつくることができますか？ URL: http://digital.ni.com/public.nsf/allkb/BE3CC7A515A3350A8625733000224136

GPIB-VXI/C Addressing A24 Address Range Error I am trying to setup a new GPIB-VXI/C board but when I try to access a specific A24 address range I get either of the following errors: "Specified offset is not accessible from this hardware." URL: http://digital.ni.com/public.nsf/allkb/5F2CCD73E35CDB18862572F100593E24

Why Does My GPIB-USB-HS Device Prompt the Add Hardware Wizard Each Time I Plug it in? Every time I unplug my GPIB-USB-HS device and plug it back in, the Add Hardware Wizard pops up and re-installs the drivers. Each time this happens I lose all of the device configuration settings. How can I avoid this? URL: http://digital.ni.com/public.nsf/allkb/13B27DA885E3F3D2862572CA0065FF70