Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

VXI/VME/PXI Controller RAM I am needing some information about the RAM on my controllers. Where can I find this information? URL: http://digital.ni.com/public.nsf/allkb/A3D1B45120A2E0B3862571A4006F5B32

Configuring the VXIpc-870 Watchdog Timer What is a Watchdog Timer and how do I configure one for my VXIpc-870 controller? URL: http://digital.ni.com/public.nsf/allkb/DBC3F9BE8597B3268625719C008294D8

Setting Up HyperTerminal to Access the GPIB-VXI/C Problem: How do I set up the serial output on my GPIB-VXI/C? Solution: You can access the GPIB-VXI/C through the serial interface. In Windows 9x/NT/2000/XP, the easiest way is to use HyperTerminal (Start » Programs » Accessories » Communications » HyperTerminal). URL: http://digital.ni.com/public.nsf/allkb/E72458D6F8C7E7D28625719C006C9C45

VXIpc-870 and VXI/VMEpc-600 Series SCSI Installation How do I install SCSI support on my VXIpc-870 and VXI/VMEpc-600 Series controllers? URL: http://digital.ni.com/public.nsf/allkb/ACC8A5F2B7A7D6EF8625719C0080A615

Changing the Resman Delay of the GPIB-VXI/C Problem: How do I change the Resman delay of the GPIB-VXI/C? Solution: The GPIB-VXI/C is factory configured such that Resman will run immediately following bootup (usually about 2 seconds). URL: http://digital.ni.com/public.nsf/allkb/E15B8F14786C3CF7862571980001861B

Converting a GPIB-VXI/C Program Using NI-488 Function Calls to NI-VISA How do I convert a GPIB-VXI/C program that uses NI-488 function calls to use NI-VISA function calls? URL: http://digital.ni.com/public.nsf/allkb/1EF040069E7B7AE086257190004D399B

将使用NI-488函数的GPIB-VXI/C程序转换成NI-VISA程序 NI Home This Document is not yet Rated Rate this Document 将使用NI-488函数的GPIB-VXI/C程序转换成NI-VISA程序 主要软件: Driver Software>>NI-VISA 主要软件版本: 3.0 主要软件修正版本: 次要软件: N/A 硬件: GPIB>>Plug-in Controllers>>GPIB-VXI/C 问题: 怎样将使用NI-488函数的GPIB-VXI/C程序转换成NI-VISA程序 解答: URL: http://digital.ni.com/public.nsf/allkb/BBA37D249DDA3553862574D10042597F

Changes to the Signal Mapping Settings for MXI-2 Interface Not Showing I changed the signal mappings for my MXI-2 interface in MAX, but they don't seem to change anything. How do I get these changes to show up? URL: http://digital.ni.com/public.nsf/allkb/55E1273776966F3D862571500052E889

如何从软盘启动PXI或VXI控制器？ 我希望通过A:区的软盘启动PXI或VXI来重新恢复操作系统，但是控制器每次总是先重硬盘启动。我需要做什么改动？或者，我希望用一张RT PXI启动盘启动我的RT系列的PXI控制器进入实时操作系统，但是控制器每次总是先重硬盘启动。我需要做什么改■> URL: http://digital.ni.com/public.nsf/allkb/4FF6BDB55381FE3B4825714A0034AFE6

Error Code 10 After Installing NI-VXI 3.3.1 NI-VXI 3.3.1 installs fine, but when I try to install my VXI hardware, I get error code 10. How can I remove this error? URL: http://digital.ni.com/public.nsf/allkb/D3B467F2AAF49050862571470042B38E