Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

NI ELVIS Calibration Wizard를 실행할때 발생하는 에러 -9311 LabVIEW에서 NI ELVIS Express VI나 에러없는 Signal Express에서 ELVIS에서 ELVIS 단계를 실행할수 있었습니다. 그러나 NI ELVIS Calibration Wizard를 실행하면, 아래 그림과 같이 에러 -9311이 발생합니다.: URL: http://digital.ni.com/public.nsf/allkb/DDC424D86F9A5F7486257171001B2935

NI ELVIS Express VIs Reset the FGEN Output When FGEN Express VI is Run in a Separate VI If I put the FGEN Express VI in a while loop in one VI and run it, and in another VI run one of the other instrument's (such as the DMM or Scope) Express VI, the second VI doesn't alter its output because the FGEN resources are still reserved by the first VI. URL: http://digital.ni.com/public.nsf/allkb/4EA75943C778290086257165007D8E4B

NI ELVIS Express VI가 FGEN Express VI가 다른 VI에서 실행될때 FGEN 출력이 리셋. 하나의 VI의 while 루프안에 FGEN Express VI를 놓고 실행하고, 또다른 VI에서 다른 장비의 Express VI(DMM 혹은 Scope와 같은 함수)를 실행하면, 두번째 실행된 VI는 FGEN의 리소스가 여전히 첫번째 VI에 예약되어 있어서 그 출력이 바뀌지 않습니다. URL: http://digital.ni.com/public.nsf/allkb/39CFF07DB5E935EB86257170001C437A

Writing to a High Digital Line with the ELVIS Digital Writer Express VI Causes Glitch When I use the ELVIS Digital Writer Express VI to write to a digital line that is already high, the line drops low before reaching the expected level. What can I do to change this behavior? URL: http://digital.ni.com/public.nsf/allkb/6DAE54F9C8B4D48586257165006B2A58

Initial High Frequency Waveform When Using the NI ELVIS Function Generator Express VI The Function Generator Express VI initially produces a waveform at a much higher frequency than I specified. Is there some way to avoid this? URL: http://digital.ni.com/public.nsf/allkb/7477AA6DE5C7E2FD862571610059DDC8

NI ELVIS Function Generator Express VI를 사용할때 초기 고주파수 웨이브폼 Function Generator Express VI 가 처음에 설정한 주파수보다 높은 주파수로 발생이 됩니다. 이것을 피할 방법이 있습니까? URL: http://digital.ni.com/public.nsf/allkb/4BB0E05F72459EEE86257170001DB743

Using an NI ELVIS Express VI in a While Loop Problem: What is the proper way to use an NI ELVIS Express VI in a While Loop? Solution: The proper way to use an ELVIS Express VI in a While Loop is to wire the stop control of that While Loop to both the Stop input of the Express VI and to the conditional terminal of the While Loop. URL: http://digital.ni.com/public.nsf/allkb/9311EF3DDF61B7218625716100789AE1

While루프 안에서 NI ELVIS Express VI의 사용 While루프 안에서 NI ELVIS Express VI의 사용하기 위한 적절한 방법이 무엇입니까? URL: http://digital.ni.com/public.nsf/allkb/AB23835948C8958986257170001EF8AF

在迴圈中使用NI Elvis Express VI。 NI Home This Document is not yet Rated Rate this Document 在迴圈中使用NI Elvis Express VI。 主要軟體: Driver Software>>NI ELVIS Driver VIs 主要軟體版本: 2.1 主要軟體修正版本: N/A 次要軟體: N/A 硬體: Multifunction DAQ (MIOConnector Blocks>>NI ELVIS 問題: 在迴圈中使用NI ELVIS Express VI最好的方法是什麼? 解答: 在迴圈中使用NI ELVIS Express URL: http://digital.ni.com/public.nsf/allkb/2D6320728D6992EF862571700008D8C2

Accessing Differential Analog Input Channels on a DAQ device When Connected to NI-ELVIS I have several signals that I would like to connect to my NI-ELVIS unit, but I only see physical connections for 5. Is it possible to access channels 6 and 7 on my DAQ device when using the NI-ELVIS? URL: http://digital.ni.com/public.nsf/allkb/6AC72AB32FF64BFB862570990065CCAD