Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

NI 9219 Convert FXP to Thermocouple VI I am using NI-RIO 2.4 with fixed point I/O and an NI 9219 in a CompactRIO. How can I convert the FXP channel value in the real-time controller or host PC to temperature units, accounting for the CJC value? URL: http://digital.ni.com/public.nsf/allkb/22C1D4F68DD27B6286257434005EA8F7

Error -63001 NI-RIO FPGA Communications Occurs With DMA Transfers From Host to FPGA I am trying to do a DMA transfer from the 900x cRIO RT controller to the cRIO FPGA. The FPGA code compiles. However, when I run the code I get a Real-Time error saying the following: Error -63001: NI-RIO FPGA Communications.Framework: (Hex URL: http://digital.ni.com/public.nsf/allkb/257AF49E2110630F8625741F0062D292

Using Fixed-Point Data Types with Integer Based IP in LabVIEW FPGA 8.5.x How can I use fixed-point data with LabVIEW FPGA Math and Analysis functions that only support integer data? URL: http://digital.ni.com/public.nsf/allkb/672BC377EE206CC08625740F00580544

在LabVIEW FPGA 8.5.x基于整数类型的IP核中使用定点数据类型 如何在只支持整数数据类型的LabVIEW FPGA数学分析函数中使用定点数据类型。 URL: http://digital.ni.com/public.nsf/allkb/67CE6F188E1C8F73862574270034B103

Why am I getting 'Required contraints (.ucf) file not found.' when I try to run an example on my NI PCI 5640R? I am trying to develop a project with my NI PCI 5640R, but I keep getting the following error: An internal software error in LabVIEW FPGA Module has occurred. Please contact National Instruments technical support at ni.com/support with following information: URL: http://digital.ni.com/public.nsf/allkb/D5A4D23482752518862573E30004D603

Why Is The Calibration of My 784x or 785x R Series Device Not Being Saved? When using the NI 78xxR Calibration Utility to calibrate my 784x or 785x R Series device, the calibration does not seem to work. Why is this? URL: http://digital.ni.com/public.nsf/allkb/FDE5C451818A93D6862573E1007770AF

Moving CompactRIO VIs with Uncalibrated Data to FPGA Targets with Calibrated Data In versions of NI-RIO prior to 2.4, C Series Modules only return binary (uncalibrated) data, which requires the host VI to apply calibration coefficients and convert the data to engineering units in software. After installing NI-RIO 2.4 or later, the default behavior for AI/AO modules is to URL: http://digital.ni.com/public.nsf/allkb/254BBC14267D2972862573E000824912

How do I access RIO devices on a networked computer? I have a system with an R-Series device that I would like to target from a different system on the network. Is this possible? URL: http://digital.ni.com/public.nsf/allkb/43F81436B97AEE28862573D40069F440

NI-RIO 2.4 Full Recommended Software Set for Single-Board RIO Devices Does Not Include NI Serial and Modbus I/O Server I want to install the full recommended software set for NI-RIO 2.4 on a Single-Board RIO device. Unlike the software sets for the cRIO-901x, cRIO-900x, and cRIO-907x, the software set for Single-Board RIO devices does not include NI Serial or Modbus I/O Server. Why are those drivers missing from URL: http://digital.ni.com/public.nsf/allkb/4F46D4DEC02BA5D5862573AE007685E9

How to enable NI 9853/9852 C-Series module support on NI cRIO-9072 or cRIO-NI 9074 platforms? I got the following error message, if i try to install a NI985x CAN module on my NI cRIO-9072 or cRIO-NI 9074 device. The NI cRIO-9852 and NI cRIO-9853 C-Series modules are not supported on the NI cRIO-9072 or cRIO-NI 9074 platforms. Please visit ni.com/info and URL: http://digital.ni.com/public.nsf/allkb/C8284F895E607E1E862573A2006D7BA9