Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

SCXI Configuration on Remote RT System Never Updates My SCXI chassis configuration in the Measurement & Automation Explorer (MAX) never changes even if modules are shuffled or changed. Why can't I delete my SCXI chassis from my RT system in MAX? URL: http://digital.ni.com/public.nsf/allkb/043D88990AB8535C86256FE80053ADA6

BNC-2096を使用してTEDSセンサの構成をするには、どのようにすればよいですか？ TEDSセンサを持っているのですが、TEDSセンサとBNC-2096を使用するには、どのハードウェアが必要ですか？また、LabVIEWで集録するには、TEDSセンサの構成をどのように行ったらよいですか？ URL: http://digital.ni.com/public.nsf/allkb/1C55B5F92D8D6CC186256FE200202F86

Erroneous or Noisy Thermocouple Readings Causing Hardware Trigger to Fail My thermocouple is returning noisy and erroneous readings when trying to trigger at a specified level using a hardware trigger within NI-DAQ and an SCXI-1102 module in an SCXI-1100 chassis. I am applying heat to the thermocouple by pinching it between my fingers. What can I do to eliminate URL: http://digital.ni.com/public.nsf/allkb/1000678F9D4B9E7F86256FD20059D053

Why Am I Getting Temperature Drift on My Thermocouples When My Cold Junction Temperature Changes? I am using a terminal block to connect my thermocouples to my data acquisition or signal conditioning device, but I notice that when the temperature of the cold junction (CJ) changes that my measurements drift. URL: http://digital.ni.com/public.nsf/allkb/C4920FDE8722A03D86256FCB0076DE6B

Why Does Measurement & Automation Explorer (MAX) Freeze When I Try to Auto-Detect My SCXI Modules Using Traditional DAQ? I go under Devices and Interfaces and right-click on Traditional DAQ Devices and Add an SCXI Chassis. I then follow the prompts selecting the Chassis Type, Chassis ID, and Chassis Address, but when I select Yes to Auto-Detect Modules Measurement & Automation Explorer (MAX) freezes. URL: http://digital.ni.com/public.nsf/allkb/0FA44B20777D77C186256F8700011D65

Thermocouple Reads a Large Negative Value When Connected to My SCXI Chassis Why does my thermocouple measure a value on the order of -1000 degrees when hooked up through my SCXI chassis? URL: http://digital.ni.com/public.nsf/allkb/F84C4728FF407E0886256F1800568241

Potential Analog Input Offset Using an Externally Powered Pressure Transducer in an SCXI System I am using an SCXI system for analog input (for example an SCXI-1100 with an SCXI-1300 terminal block) and measuring voltage from a pressure transducer that requires an external power source. Why do I see a constant offset over the entire range of my measurement? URL: http://digital.ni.com/public.nsf/allkb/4BB6C879B6055E7386256ED300676D72

Why Am I Getting # inf or # j When Running A Shunt Calibration With My SCXI 1520 Module? I have a SCXI 1520 strain module with a 1314 terminal block. I am certain that my strain gauge is wired in correctly but I receive a # inf or # j error when running a shunt calibration. My strain gauge is a quarter bridge I bridge type. URL: http://digital.ni.com/public.nsf/allkb/33F09F8A218914B386256E9800518842

What Are The Pinouts of the SCXI-1180? NI Home 2 ratings: 4 out of 5 Rate this Document What Are The Pinouts of the SCXI-1180? Hardware: SCXI>>Terminal Blocks Problem: The SCXI-1180 manual does not list the pinouts for the module. Solution: The SCXI-1180 pinouts can be found in the following table: 50-pin Connector E-Series MIO Board URL: http://digital.ni.com/public.nsf/allkb/B2889ADCFD4B915986256E830081790F

Triggering with PFI 7 on the SCXI-1600 What is PFI 7 on the SCXI-1600? Why does my computer crash when I attempt to trigger off it? URL: http://digital.ni.com/public.nsf/allkb/95EFEE3EF3E643EE86256E82006BAF18