Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Ghosting on Motion Controller Analog Inputs I have an NI-73xx Motion controller and I am using the analog input to read an analog signal. I have hooked up my signal to analog input channel 3, but in my program I am reading from analog input 1. Even though I am reading from a different channel than what I have connected, I still see URL: http://digital.ni.com/public.nsf/allkb/9CDFFA9DB8A876A48625733C0012796E

Digital Output on Motion Controller Not Functioning I have a PCI-7350 and am trying to output signals on the DIO lines in Measurement and Automation Explorer (MAX) and using Set I/O Port MOMO.flx. I can read the inputs on the first port, but line 5 on the second port never has any output and I never see any output on the third port. Why do my URL: http://digital.ni.com/public.nsf/allkb/6363F79BE8031EF38625722D007D5E65

Motion 컨트롤러의 디지털 출력이 동작하지 않습니다. PCI-7350를 가지고 있고 MAX(Measurement and Automation Explorer)에서 DIO 라인들에서 신호를 출력하려고 하고 Set I/O Port MOMO.flx를 사용하려고 합니다. 첫번째 포트에서는 입력들을 읽을수 있습니다. 그러나, 두번째 포트의 라인 5 에서는 어떤 출력도 나오지 않고, 세번째 포■> URL: http://digital.ni.com/public.nsf/allkb/B78A4910D6362260862572360008CD27

Changing Motion Controller Settings on Default 73xx Settings Page in MAX I am using a PCI or PXI NI Motion device, and I have selected and saved settings for each individual axis in MAX. When I go to the page titled 'Default 73xx Settings' and make any selections, it immediately erases all of my previous settings. Is this expected behavior? URL: http://digital.ni.com/public.nsf/allkb/0C34A033AAC0EA7C8625721700741D36

MAX에서 디폴트로된 73xx 설정페이지에서 Motion 컨트롤러 설정변경 PCI 또는 PXI NI Motion 장비를 사용하고 있고, MAX에서 각각의 축에 대해서 설정을 선택하고 저장하였습니다. 'Default 73xx Settings' 이라는 제목의 페이지로 가서 어떤 선택을 하게되면 제가 이미 해놓았던 모든 설정들이 즉시 지워지게 됩니다. 이런 동작이 정상적인 것입■> URL: http://digital.ni.com/public.nsf/allkb/17E2FF682F38C2FC862572360007E099

在MAX的默认73XX设置页中改变运动控制卡的设置 我在使用一块NI的PCI 或 PXI 运动控制设备, 我已经在MAX中为每个轴选择和保存了设置.当我进入名为 "Default 73xx Settings" 的页面，进行设置时，它立即删除了我之前进行的所有配置. 应该是这样吗？ URL: http://digital.ni.com/public.nsf/allkb/ACE504ADDD02E52D862574000018A081

PCI/PXI-7344やUMI-7764/7774をフォトカプラ入力のモータードライバと接続する場合の接続方法 UMI-7764/7774をステッピングモーターメーカーのモータードライバに接続して使おうとしています。モータードライバはフォトカプラ入力になっています。どのように接続したらいいですか？ URL: http://digital.ni.com/public.nsf/allkb/9599D6CFD783C8238625710F00173331

MID-760xに接続できるステッピングモータ ５線式（５ワイヤ）の２相ステッピングモータをMID-760xに接続しようと思っていますが、マニュアルに該当する接続方法の図がありません。５線式の２相ステッピングモータは接続できないのですか？MID-760xに接続できるステッピングモータはどのような形■> URL: http://digital.ni.com/public.nsf/allkb/8BCB4888A9453674862570FC001E79BB

Why Does My Vertical Stage Drop Several Counts Instead of Stopping When it Finds Home? I am using a servo motor and I have written a LabVIEW program to find a home limit switch on my vertical stage. The stage moves appropriately while searching for home. It first moves in the forward direction and if it reaches a forward limit, it moves in the reverse direction until it finds URL: http://digital.ni.com/public.nsf/allkb/57B752BEFDE153D78625707C00668EA3

Generating a Move Results in Axis Vibration When I send a move to my motor, the axis seems to vibrate in place, but it does not move. I have tried a variety of move distances, velocities, and accelerations, but the motor still doesn’t seem to ever move out of its initial position. What is causing this behavior? URL: http://digital.ni.com/public.nsf/allkb/883E53D872CC87B286256F33006D45F1