NI PXI-2535 or PXI-2536 FET Switch Doesn't Close
I am using an NI switch module with fault protected FET switches (e.g. PXI-2535 or PXI-2536). The module typically works as it should, but sometimes I notice that the signal path reads open even after a command is sent to close the switch. I've noted this can happen when using the fault prote
URL: http://digital.ni.com/public.nsf/allkb/FD603AF66DCC934386257403006C4109
|
LFH200 Bare Wire Cables with Date Codes 3707 and 5007 Have Incorrect Pinouts
On the LFH200 Bare Wire cable, Leg J2, Leg J3, Leg J6 and Leg J7 have mismatched wire color codes when compared with the pin assignment table given in the LFH200 Cable Installation Instructions. This
URL: http://digital.ni.com/public.nsf/allkb/F6C3FFFAC2A65970862573E7007F822E
|
Difference between Switch Resistance and Path Resistance in FET Switches
I am using an NI Switch module with FET switches (such as the PXI-2501). I notice in the module's specifications document that the total path resistance is significantly larger than the FET switch on resistance. Why is the overall path resistance so much larger than the on resistance
URL: http://digital.ni.com/public.nsf/allkb/B7000E91539ED72A86257336000D105E
|
Troubleshooting an ER 16 Behaving Incorrectly
The relays on the ER 16 are not behaving as expected when being controlled by PCI-DIO 32HS (6533). In the MAX Test Panel, when writing to the ports, the corresponding LEDs on the ER 16 do not behave as expected.
URL: http://digital.ni.com/public.nsf/allkb/F03497B561D77749862570140062F5EF
|
開発用PCで作成した 'Switch Executive Configuration' ファイルをどのようにしてターゲットPC（他のPC）に配布しますか？
'Switch Executive' を使用してアプリケーションを構築しています。同様のシステムが幾つかあるのですが、開発用PCで設定した 'Switch Executive' の構成をどのようにしてターゲットPCに配布しますか？
URL: http://digital.ni.com/public.nsf/allkb/94E1AD5B5572C9CD86256FD5001B0960
|
Error -1074118655, -1073807343 o -1074118644 Ocurre Cuando se Direcciona a un Instrumento PXI
Cuando trato de abrir una sesión para mi Instrumento PXI (NI-DMM, NI-FGEN, NI-SCOPE, NI-HSDIO, NI-SWITCH) o intento validar mi dispositivo virtual en NI Switch Executive, obtengo uno de los siguientes errores. ¿Qué significa esto?
URL: http://digital.ni.com/public.nsf/allkb/4FA13293B85321868625741E00760C80
|
Error -1074118655, -1073807343 or -1074118644 Occurs When Addressing a PXI Instrument
When I try to open a session to my PXI instrument (NI-DMM, NI-FGEN, NI-SCOPE, NI-HSDIO, NI-SWITCH) or try to Validate my Virtual Device in NI Switch Executive, I get one of the following errors. Why is this?
URL: http://digital.ni.com/public.nsf/allkb/8130049893D6461E86256F3B00461E1B
|
PXIデバイスのアドレス設定で、Error -1074118655、 -1073807343、 -1074118644が発生するときの回避方法
PXIモジュール型計測器[NI-DMM, NI-FGEN, NI-SCOPE, NI-HSDIO, NI-SWITCH]とセッションを開こうとすると、エラー[-1074118655、 -1073807343、 -1074118644]になってしまいます。これはなぜですか？
URL: http://digital.ni.com/public.nsf/allkb/033CC9D6A549D15586256FE400042E7A
|
PXI-2593 or SCXI-1193 Does Not Make Connections but Gives No Errors
When I run a program that uses my PXI-2593 or SCXI-1193, everything seems to run fine with no errors. However, when I check my connections for continuity, the connections are not made. Why is there such a discrepancy?
URL: http://digital.ni.com/public.nsf/allkb/3B5BC68C1DD1BDBE86256EFD006EE2A0
|
Which SCXI Controller(s) and Kit(s) Will Work with My SCXI Switch?
Problem: Which SCXI controller(s) and adapter kit(s) will work with my SCXI switch? Solution: The NI Switches Getting Started Guide contains a table entitled SCXI Controllers and Supported SCXI Switches that specifies which SCXI controllers and kits are supported by each SCXI switch.
URL: http://digital.ni.com/public.nsf/allkb/BAC82D57A9BB756086256DDB000CA92D
|
