Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Why is Incorrect Data Retuned When Communicating via Interactive Mode with NI-RIO 2.1.3 or Earlier? I Have and NI RIO application that performs array read/writes on a cRIO 901x controller that has NI RIO 2.3 and LabVIEW Real-Time 8.5 installed that returns incorrect data. When running in host interface mode, I get a LabVIEW Real-Time error about incompatible versions on the remote target URL: http://digital.ni.com/public.nsf/allkb/ACFAFB6C516C7C904825735300774D04

NI-Sync 3.0 Fails on Startup when Running RT I just installed NI Sync 3.0 and my startup application VI fails on my RT target. niSync Initialize returns 0xBFFF400A on startup URL: http://digital.ni.com/public.nsf/allkb/EF18A0733AE845188625734500567A57

Ghosting on Motion Controller Analog Inputs I have an NI-73xx Motion controller and I am using the analog input to read an analog signal. I have hooked up my signal to analog input channel 3, but in my program I am reading from analog input 1. Even though I am reading from a different channel than what I have connected, I still see URL: http://digital.ni.com/public.nsf/allkb/9CDFFA9DB8A876A48625733C0012796E

Why do I see Spurious Returns when using multiple Wait on IRQ Nodes on VxWorks Real Time Targets? NI-RIO 2.3 with LabVIEW 8.5 supports multiple Wait on IRQ nodes in a single VI, however, I see spurious returns from the "Wait on IRQ" Method Node when using cRIO-901x Controllers. This does not occur on my cRIO-900x Controllers or any other Pharlap based Real-Time controller. Why does this URL: http://digital.ni.com/public.nsf/allkb/A868BA261986A486482573380077794D

cFP-180x Firmware Upgrade Fails on the 10.0.54 Subnet The firmware upgrade fails when my cFP-180x is on the 10.0.54 subnet. It begins to upgrade and then terminates. How do I get around this? URL: http://digital.ni.com/public.nsf/allkb/6A9C6B3D1BE8DA5786257338007B9080

當我在VxWorks Real Time Targets環境下使用多個Wait on IRQ節點時，為何會得到假的回傳值？ NI-RIO 2.3搭配LabVIEW 8.5的使用可以支援在單一VI中使用多個Wait on IRQ節點。然而，當我使用CRIO-901x控制器時，會從"Wait on IRQ" 節點得到假的回傳值。這個現象並不會發生在cRIO-9000x或其他Pharlap的Real-Time控制器。這個問題發生的緣由為何呢？ URL: http://digital.ni.com/public.nsf/allkb/95BC4E473B7C6313862573AD00070404

Why Do I Get Error 50202? I am using NI software and I get error 50202. What is going on? URL: http://digital.ni.com/public.nsf/allkb/61060FCCEFD2D5EF86257337005B9ED7

NI-VISA 4.2 이상의 버전을 설치한 이후에 MAX에서 CompactRIO 컨트롤러가 보이지 않는 이유 최근에 NI-VISA를 업그레이드한 후, MAX에서 CompactRIO 컨트롤러가 보이지 않는 현상이 발생합니다. URL: http://digital.ni.com/public.nsf/allkb/6F612762E0CB18508625733A0003B808

Why Does My CompactRIO Controller Not Appear in MAX after Installing NI-VISA 4.2 or Later? I recently upgraded NI-VISA and can no longer see my CompactRIO controller(s) in MAX. What could be the problem and how can I fix this problem? URL: http://digital.ni.com/public.nsf/allkb/1C24D45C2850C5F6862573280013EDF8

为什么安装了NI-VISA 4.2及之后版本，我的CompactRIO控制器在MAX中看不到 最近我升级了NI-VISA然后在MAX中找不到CompactRIO控制器了，问题出在哪里如何解决？ URL: http://digital.ni.com/public.nsf/allkb/42ECB8B0DC1ADCB7862573A3001339C0