Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

NI 運動控制卡上數位 I/O 的最高速度 NI 運動控制卡上的的數位 I/O 可以以多高的速度來做輸入或輸出？ URL: http://digital.ni.com/public.nsf/allkb/636AA5C94EF8561A862573B600429366

Positive and Negative Terminals of an NI Motion Controller’s Step and Direction Outputs The Step and Direction inputs on my drive require Step +, Step -, Dir +, and Dir – signals. What are the corresponding outputs on my National Instruments 73xx motion controller? URL: http://digital.ni.com/public.nsf/allkb/BB33DB9B8CCF1BC486257134006F3FA5

Maximum Cable Lengths for NI Motion Hardware What is the maximum cable length that can be used to connect between an NI Motion Controller and an NI Universal Machine Interface(UMI) and between the UMI and the motor power drive? URL: http://digital.ni.com/public.nsf/allkb/72B2B42E1819E2AE8625711D000D931E

NI Motion硬件的最大线缆长度 连接NI Motion 控制器和NI Universal Machine Interface(UMI)之间，以及连接UMI到电机功率驱动之间的线缆最长是多少？ URL: http://digital.ni.com/public.nsf/allkb/BC74AE3E1F15D7498625740000198C3A

UMI-7774/7772的+5V可以輸出多少電流? 我使用UMI-7774將馬達driver跟encoder連接到馬達控制卡上，我想使用Feedback Connector上面第四pin和第八pin的+5V去驅動encoder，UMI-7774的使用手冊上寫著'UMI-7774/7772由內部電源供應器所產生的電源可以驅動encoder'。請問這個輸出電源可以產生多少電流? URL: http://digital.ni.com/public.nsf/allkb/DE9E9DEDBF77883986257169004C0765

UMI-7774/7772의 전원 +5V 전류 출력은 얼마인가요? 모션 제어기와 UMI-7774를 연결하여 모터 드라이버와 엔코더를 사용하고 있습니다.+5V 파워를 사용하여 엔코더에 피드백연결을 4개 핀에서 8개 핀을 연결하여 사용하고 싶습니다.UMI-7774의 사용자 메뉴얼에 출력 상태 표시를 'UMI-7774/7772 내부 파워 공급이 제공되 URL: http://digital.ni.com/public.nsf/allkb/B5C30055ED20CB6F86256FB500392227

What is the Current Output of the +5V Power on the UMI-7774/7772? I am using the UMI-7774 to connect my motion controller to my motor drive and encoders. I would like to use the +5V power available on pin 4 and pin 8 of the Feedback Connector to drive my encoders. The UMI-7774 user manual states that these outputs, 'generated by the UMI-7774/7772 internal power URL: http://digital.ni.com/public.nsf/allkb/A70E4C6A7A6AE61C86256FA3006458B3

Can I Use a New FlexMotion Board with My Old Version of LabVIEW? I am using LabVIEW 5.1 and I am looking to integrate a new motion controller, the PCI-7332, into my application. When I look at the product reference for the PCI-7330 series, I see that I would need NI-Motion 6.1 or later, which does not support LabVIEW 5.1. What can I do? URL: http://digital.ni.com/public.nsf/allkb/A2EE6C05A85333AA86256F400076E41D

Can I Downgrade the Firmware on My FlexMotion Controller? I have a motion system in which I am using an older version of NI-Motion. Because I needed the controller in a different location, I moved it to another computer that was using a newer version of NI-Motion. When I did this, I had to upgrade the firmware on the controller in order for it to URL: http://digital.ni.com/public.nsf/allkb/8AC57269C7674C3C86256F3800768207

モーションコントローラ(FlexMotion Controller)のファームウェアのダウングレード 古いバージョンのドライバで動作させているモーションのシステムがあります。 システムを増設するために、別なPCで動作させていたモーションのボードを使おうと考えています。 以前購入したボードは、新しいドライバがインストールされたPCで動作させる URL: http://digital.ni.com/public.nsf/allkb/FB44A016D2B1D1398625719A001A1144