Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

How Does the BCR Register Interaction With Internal State Machines in GPIB ASICs I am using the NAT9914 GPIB Talker/Listener chip. I noticed that the BCR (Bit Control Register) can be used to set certain bits on the GPIB. How does this affect the internal state machines of the 9914? Will the BCR override them? URL: http://digital.ni.com/public.nsf/allkb/74FEC0802618241086256E85005B347A

Why Can't My GPIB-ENET or GPIB-ENET/100 Device Respond To Pings? I have my GPIB-ENET (or GPIB-ENET/100) device configured with a valid IP address in MAX, but it times out when I try to ping it. Why won't my device respond to pings? URL: http://digital.ni.com/public.nsf/allkb/D4A705A42207131186256E84007F3FD3

为何我的GPIB-ENET(GPIB-ENET/100)设备不能响应Ping命令？ 我在MAX中给我的GPIB-ENET(GPIB-ENET/100)设备配置了一个可用的IP地址，但是在我尝试Ping这个设备时，总是超时。为什么我的设备不能响应Ping命令？ URL: http://digital.ni.com/public.nsf/allkb/A8DDBC407E96AFE286256EB600097012

Execution Difference Between GPIB-ENET and PCI-GPIB My program works fine with the GPIB-ENET, but when I run the same exact program on my PCI-GPIB card, the instrument hangs and I get errors. I try looking at the calls in NI-SPY but when I use that, the program works again. URL: http://digital.ni.com/public.nsf/allkb/D4C4FC3AF557D22A86256E7F0054A6F8

GPIB-ENET와 PCI-GPIB 사이에 실행 차이 GPIB-ENET에서 잘 동작하는 프로그램을 PCI-GPIB 카드를 사용해서 실행하면 장비가 정지하고 에러가 발생합니다. NI-SPY를 통해서 호출을 확인하려고 시도하면 그 때에는 프로그램이 다시 동작합니다. URL: http://digital.ni.com/public.nsf/allkb/7A0B4290534DDFC486256E9200160C5D

Performing a Good Analyzer Capture for Debugging/Troubleshooting What are the best settings for the GPIB Analyzer if I am trying to troubleshoot a complex GPIB problem that may involve handshaking between multiple devices, bus timing, and the lower-level details of the 488.1 standard? URL: http://digital.ni.com/public.nsf/allkb/ABA74984DA039B2286256E6F007B0082

Do I Need To Wait for the TNT5002 Chip to Reset Before Reading/Writing Registers? If I am developing a GPIB instrument using the TNT5002 and assert the RESET# line, how long do I have to wait after deasserting it before I can perform my next read/write to the registers on the ASIC? URL: http://digital.ni.com/public.nsf/allkb/EAAD6AA3249C204286256E69000C8773

GPIB ENET/100 장치의 이더넷(Ethernet)설정은 어떻게 하나요? GPIB ENET/100 장치를 가지고 Ethernet 설정을 하려고 합니다. 어떻게 해야하나요? URL: http://digital.ni.com/public.nsf/allkb/59D7730B3A4BDCA886256E930002EF95

Difference Between Static and Pulsed I/O on the NAT9914 The NAT9914 Reference Manual refers to both Static and Pulsed I/O operations. Specifically, what is the difference between Static and Pulsed I/O? URL: http://digital.ni.com/public.nsf/allkb/C433CBB5F03774F286256E5A005ED629

Implement the Count Method of Termination When Programming the NAT9914 How do I implement the count method of termination when programming the NAT9914? URL: http://digital.ni.com/public.nsf/allkb/642FC7A5B109958186256E5A007C5290