Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

How Do I Use the VI Digital Group Config.vi with the 8255 chip (lab*, PC-DIO*, etc.)? How does Digital Group Config.vi work with the 8255 based devices like the PC-DIO series? URL: http://digital.ni.com/public.nsf/allkb/C1C9B9F736A8B116862565590079437A

Why Do I Get Error -10010 with my NI 6533/6534 Board? If I configure the NI 6533/6534 for handshaking/pattern generation on one port and set the buffer size to an odd number of bytes, then I get error -10010. URL: http://digital.ni.com/public.nsf/allkb/323223711E9298DF862565450079DAB7

DAQCard-1200, PCI-1200, and Lab-PC-1200 Missing a Diode that Will Impact RSE Readings Certain revisions of the DAQCard-1200, PCI-1200, and Lab-PC-1200 are missing a diode that will impact RSE (referenced single-ended) readings. URL: http://digital.ni.com/public.nsf/allkb/A4A676D431CC6D60862564F0006CE0C1

How Do I Synchronize 3 E-Series Boards Using 3 SC-2040's? Explicitly enable output on PFI 7 and make it output the Scan In Progress signal (using the Route Signal VI or Select_Signal VI in NI-DAQ). URL: http://digital.ni.com/public.nsf/allkb/322C57E34AF5E2398525638C0045EC55

Data Dropout / Flatlining during Analog Output Waveform Generation. I am doing analog waveform generation using an AT-MIO-16F-5. My output data buffer is smaller than 64 KB (or 32,768 data points), but when I start generating the waveform, I see periodic flat lines on the output and I get a NI-DAQ warning code 15 (given buffer requires DMA reprogramming at run URL: http://digital.ni.com/public.nsf/allkb/0B69A516D8032234862562BB0008C4DF

Starting a Data Acquisition with an External Digital Trigger Pulse Using a PC-LPM-16 or a DAQCard-700 How can I start a data acquisition with an external digital trigger pulse using a PC-LPM-16 or DAQCard-700? URL: http://digital.ni.com/public.nsf/allkb/5E74D8A479823BDF862562B3005D9399

AT-MIO-16E-2 는 SCXI-1102 에서 채널을 스캔하는데 있어unipolar 와 bipolar 모드를 함께 쓰지 못합니다. AT-MIO-16E-2 와 SCXI-1102 에서 채널을 스캔하는데 있어unipolar 와 bipolar 모드를 함께 쓰는데 잘못된 데이타를 받는 이유는 무엇인가요? URL: http://digital.ni.com/public.nsf/allkb/9987689267DF40ED86256F250039442C

Time out on pre-triggger operation in LV on a legacy AT-MIO-16. Problem: What pin do I connect my digital trigger to on a legacy AT-MIO-16 board? Solution: When using a digital trigger on a legacy AT-MIO-16 board you need to connect the trigger to the 'Start Trig' pin of the board if the operation has no pre trigger scans. URL: http://digital.ni.com/public.nsf/allkb/37F8D46C70ECDD43862561DD004FDB24

使用LabVIEW對舊的AT-MIO-16預觸發動作逾時。 NI Home This Document is not yet Rated Rate this Document 使用LabVIEW對舊的AT-MIO-16預觸發動作逾時。 硬體: Legacy DAQ Devices>>Multifunction DAQ>>AT-MIO-16 問題: 我應該將數位觸發訊號接舊的AT-MIO-16上那個腳位？ 解答: 當在舊的AT-MIO-16使用數位觸發，您需要將它接到"'Start Trig"，如果不需要觸發前的資料。或是將它接到'Stop Trig' 如果需要觸發前的資料。 相關連結: 附加檔案: 報告日期: 06/16/1995 最後更新: URL: http://digital.ni.com/public.nsf/allkb/836559477B79BEED86256ECA00074418

Can I Use the 1 MHz Internal Clock as the Source on the DAQCard-700? How do I use the internal 1Mhz clock on the DAQcard-700 as the source for counter 1 using NI-DAQ calls? URL: http://digital.ni.com/public.nsf/allkb/0D1DCF7561C751A586256E8E00250C50