Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

使用LabVIEW对旧的AT-MIO-16预触发动作超时。 NI Home This Document is not yet Rated Rate this Document 使用LabVIEW对旧的AT-MIO-16预触发动作超时。 硬件: Legacy DAQ Devices>>Multifunction DAQ>>AT-MIO-16 问题: 我应该将数字触发信号接到旧的AT-MIO-16上哪个针脚？ 解答: 当在旧的AT-MIO-16使用数字触发，如果不需要触发前的资料，您需要将它接到"'Start Trig"。或是如果需要触发前的資料，将它接到'Stop Trig'。 相关链接: 附件: 报告日期: 11/23/2006 最近更新: URL: http://digital.ni.com/public.nsf/allkb/F7AECFA2A608A64A4825722F0011ADA0

ELVIS 1.0 Returns “Requested Value is Not Supported Value For This Property” Error – Error # -200077 I have a DAQcard 700 and ELVIS 1.0. Whenever I start ELVIS 1.0, I get the error “Requested value is not supported value for this property” – error # -200077. What is causing this problem? URL: http://digital.ni.com/public.nsf/allkb/C4F82AF1E218F5AC86256F32005B5F70

ELVIS 1.0에서 '요청한 값은 지원되지 않습니다.-에러 # -200077'라는 에러가 발생합니다. DAQcard 700과 ELVIS 1.0을 사용하고 있는데, '요청한 값은 지원되지 않습니다.-에러 # -200077'라는 에러가 발생합니다. 이 에러의 원인은 무엇인가요? URL: http://digital.ni.com/public.nsf/allkb/C0C0E4A7F792D55086256FDB0014378C

Interval Scanning, Simultaneous Sampling, and Round-Robin Scanning Support I am developing an application using some of your data acquisition boards on which I am acquiring from multiple channels. It is very important for me to know exactly how the different channels are getting sampled. Are they scanned one after another or are they sampled at exactly the same time? URL: http://digital.ni.com/public.nsf/allkb/4F9D107D8B26233B86256F250057C9B3

AT E Series Device가 NI-DAQ 7.0 또는 7.1에서 정확히 동작하지 않습니다. NI-DAQ 7.0 또는 7.1에서 AT E Series devices를 사용할 때, MAX의 Test Panel에서 Device is not responding to the first DMA channel 에러가 발생하였습니다. Device Manager에 따르면 3개의 모든 DMA 채널이 맞게 설정된것처럼 보이나 MAX Test Panel에서는 Device의 첫번째 DMA 채널 URL: http://digital.ni.com/public.nsf/allkb/3708A7220794B66986256EC4002CB3B8

How Are the ACK and REQ Lines Controlled on the 653x DIO Devices? I am developing an application that will be using the Handshaking I/O Burst Protocol on my 653x device. I am a little unclear as to how the ACK and REQ lines are used. What controls these lines, and do I need to programmatically set one of these lines when I am ready to transfer data? URL: http://digital.ni.com/public.nsf/allkb/CDFED34BD265F95F86256E220072B01A

Group Assignments for Digital I/O 653x Applications How should I assign the group numbers for digital I/O applications using the 653x ? URL: http://digital.ni.com/public.nsf/allkb/275716F5406C9EB986256C4C000B2CB2

How do I Synchronize the Analog Input with the Analog Output on My DAQCard-1200? My DAQCard does not have the RTSI bus, so how do I synchronize the analog input and analog output of my acquisition? URL: http://digital.ni.com/public.nsf/allkb/8683A17AED4FDBAB86256C1E006D3BBA

What is Reglitching and How Do I Use it? The specifications in the user manual of my data acquisition (DAQ) board refer to a property called 'Reglitching'. What is reglitching? When should I use it? How do I enable it? URL: http://digital.ni.com/public.nsf/allkb/148DB1D40AA37B2D86256BDE005F772A

DIO Board with External Connections Fails Resource Test I have a PCI-DIO-32HS high-speed digital I/O board that is connected through a terminal block to various signals that are sourced from another external device. When I disconnect the terminal block (and thus disconnect the signals), the board will pass the resource test in Measurement & URL: http://digital.ni.com/public.nsf/allkb/E8E8657EBCD3606586256B60006D9D50