Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Setting the Transceiver Wire Mode on Ports for National Instruments Serial Boards How can I set the transceiver wire mode for ports on my National Instruments serial boards? URL: http://digital.ni.com/public.nsf/allkb/1D516C10D7EDFAC6862571110073B8F4

对National Instruments的串口卡进行端口的收发线模式设置 如何对National Instruments的串口卡进行端口的收发线模式设置? URL: http://digital.ni.com/public.nsf/allkb/3E821A4AC1954A75862573C7004FDA8C

Cannot Log Into Computer After Installing My Serial Board I have a PCI Serial card for which I installed the drivers and that went smoothly. However, after I actually install the board, my computer freezes up when I'm trying to log in to the network. What could be causing this? URL: http://digital.ni.com/public.nsf/allkb/C08967C7A685A3FE862570F4006DD596

MAX상의 'Open VISA Session' 옵션에서 무슨 문제가 발생한 것입니까? VISA 드라이버 3.3버전을 설치하였습니다. 그런데 Measurement and Automation (MAX)상의 'Open Visa Session' 옵션이 더이상 존재하지 않습니다. 현재 보이는 옵션은 'Open Visa Test Panel' 이 전부입니다. VISA Test Panel을 열면, 동일하게 동작하지만, 해당하는 옵션과 탭이 존재하지 않습■> URL: http://digital.ni.com/public.nsf/allkb/277AC4250D3B6A538625704A00027609

What Happened to my 'Open VISA Session' Option in MAX? I just installed version 3.3 of the VISA drivers and I no longer have the "Open Visa Session" option in Measurement and Automation Explorer (MAX). All I have now is "Open Visa Test Panel." When I open the VISA Test Panel, it works the same, but there are options and tabs missing. URL: http://digital.ni.com/public.nsf/allkb/CAF8CCD8F3FE074F8625703B007D8C67

Configure Serial ENET Device to Plug Directly into PC Enter a Subnet Mask such as 255 0 0 0. The subnet mask is a code that helps the network device determine whether another device is on the same network or a different network. URL: http://digital.ni.com/public.nsf/allkb/65887B258DE2A36386256FC00083D2BC

Handshaking in Serial 485 Two Wire Modes I could not find any documentation on when the CTS, RTS, and DTR lines are used in the Serial 485 - Two Wire Transceiver Modes. What are these for? URL: http://digital.ni.com/public.nsf/allkb/3417A78E145D6D6586256F3B005E8503

串口485两线模式中的握手 在串口485的任何文档中，我都找不到何时使用 CTS, RTS, 和 DTR 线的说明 - 两线传输模式. 它们用来做什么的? URL: http://digital.ni.com/public.nsf/allkb/D9619234FA7DFCCA862573C7004D0176

Using NI-VISA to Communicate with Third-Party Serial Card I purchased a third-party serial card. After installation, the device is showed working properly under device manager in Windows 98 but it was not listed under Measurement & Automation Explorer(MAX), does that mean I can not use NI-VISA to control that device? URL: http://digital.ni.com/public.nsf/allkb/7691827728AF681886256F270057337B

Maximum Transfer/Baud Rate with PCMCIA Serial Communication Devices I have a PCMCIA serial communication device that I am trying to configure in Measurement and Automation Explorer (MAX). When I go to the COM port and click on the Port Settings tab, it gives me the option to select my Baud Rate. When I try to set the Baud URL: http://digital.ni.com/public.nsf/allkb/DBDCFCBBCE15ACB286256F15006EE256