Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Conflicto en los Valores del Rango en una Tarea de Termopares Causa el Error -200077 Cuando los valores máximos y mínimos especificados como el rango de temperatura de una tarea de un termopar exceden el rango de valores utilizados al calibrar dicho URL: http://digital.ni.com/public.nsf/allkb/63C3E4ACC8A5FBD78625738400067478

Error -200077 (0xFFFCF273) During Thermocouple Measurements with SCB-68 or SCXI Why is using a DAQ device with the SCB-68 or SCXI-1102 for Thermocouple Measurements with Built-In CJC Compensation Yield -200077 Error? URL: http://digital.ni.com/public.nsf/allkb/E740DA479107B1468625703B0077037B

Error -200077 (0xFFFCF273) al Realizar Mediciones con Termopares utilizando un SCB-68 o un SCXI ¿Por qué al utilizar un dispositivo DAQ con un SCB-68 o un SCXI-1102 para Mediciones de Termopares con Compensación de Unión Fría (CJC) Interna (Built-In) URL: http://digital.ni.com/public.nsf/allkb/B5C1198004968935862573840003C1ED

SCB-68 또는 SCXI로 Thermocouple을 측정하려고하면 -200077(0xFFFCF273)에러가 발생합니다. SCB-68 또는 SCXI-1102 내부에 있는 CJC 보상회로를 이용하여 DAQ장비로 Thermocouple 측정하려고 하면 왜 -200077(0xFFFCF273)에러가 발생합니까? URL: http://digital.ni.com/public.nsf/allkb/97852302224A53EC862571BD000A9C19

SCXI Chassis Need to Have Different Addresses Even when Controlled by Different Controllers nbspI have two executables using NI-SWITCH that initialize different switch modules in two different SCXI chassis. They are controlled with different MIO boards. I get an error when trying to run the 2 executables together, stating that there is already an open driver session to the switch. URL: http://digital.ni.com/public.nsf/allkb/627B7C5C5101C9A586256FD60083B106

Why Does the Device Reset.vi in LabVIEW Return Status 0 When the SCXI-1000 is Powered Down? If the Device Reset.vi in LabVIEW is called with SC1 as the string input, which should attempt to reset the SCXI chassis, and the SCXI-1000 chassis powered down, it still returns a 0 status.Steps to Reproduce:Run the Device Reset.vi in LabVIEW with SC1 as the string input URL: http://digital.ni.com/public.nsf/allkb/AA7F6EDFE3E1302E86256FD500817568

Resolving the 'Unable to Test Chassis at This Time' Error When I try to test my SCXI system, I get the error message, 'Unable to test chassis at this time.' What could be the cause for this error and how can I resolve it? URL: http://digital.ni.com/public.nsf/allkb/ACFA07282FDC306186256FBA00799C72

Error -713 When Writing to TEDS EEPROM I am trying to write to the EEPROM of a TEDS sensor connected to a 1314T terminal block on a SCXI-1520 in an SCXI chassis, using an example that I downloaded from the web. I keep getting Error -713 "No EEPROM is detected." After URL: http://digital.ni.com/public.nsf/allkb/1BF6BC36A125E5E586256FA900692DF2

Why Is the 1000DC SCXI Chassis Power Light Blinking On and Off? I've had the SCXI 1000 DC chassis working fine for awhile now with my 4 modules in tact. Suddenly today the power light began blinking on and off. Is this indicative of anything? What is going on? URL: http://digital.ni.com/public.nsf/allkb/5F59C1AB209FEF3E86256F8D006BB252

Why Can't I Reset the Excitation Voltage of my SCXI-1520 After I Power Cycle It? I am running a SCXI-1000 chassis with a SCXI-1520 strain gague module. I can run my LabVIEW program that sets up the DAQmx virtual channel and set the excitation voltage to 5 volts. After power cycling the SCXI chassis the excitation voltage returns to zero (this is expected). If I run the program URL: http://digital.ni.com/public.nsf/allkb/7404AB31C468BF2986256F24004E77BC