Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Error -201168 with NI PXIe-5442 Firmware Why do I get error -201168 when using NI PXIe-5442 after upgrading to FGEN driver version 2.5.1? URL: http://digital.ni.com/public.nsf/allkb/9A015075CAD0869D862573CA007B177C

用NI-FGEN产生波形时的常见问题 当我使用NI-FGEN产生波形时，遇到错误 -1074118518 或错误 -1074118520。什么原因导致这些错误的? URL: http://digital.ni.com/public.nsf/allkb/4FBAC9B6FADB38DC4825729B0022FE71

Frequently Asked Questions about Streaming Waveforms using NI-FGEN I receive Error -1074118518 or Error -1074118520 when I try to stream waveform data using NI-FGEN. What is causing these errors? URL: http://digital.ni.com/public.nsf/allkb/F966BB54C613BF7986257299007E6690

为什么在虚拟Bench-Arb中使用NI 5401波形发生器会产生10401错误 在虚拟Bench-Arb软件中我无法使用NI 5401信号发生器。每次我都会遇到10401的错误，软件中显示的错误描述如下：“The specified device is not a National Instruments product, the driver does not support the device (for example, the driver was released before the device was supported), or the device has not been conf URL: http://digital.ni.com/public.nsf/allkb/5C9F5187F73509624825718B00159FCA

Specific scripts cause incorrect behavior when using script triggers in NI-FGEN 2.4 The Script language introduced with niFgen 2.4 and used by the NI Signal Generator products is a very flexible technology. There are a few very specific scripts that do not work as they should. These scripts involve nesting a “repeat until scriptTriggerX” instruction in a “repeat Forever” URL: http://digital.ni.com/public.nsf/allkb/63528A0EF3D52F418625712200800DE5

My PCI-6704 Fails the Self-Test in MAX When I Attempt to Open a Test Panel When I try to open a traditional test panel in MAX v3.1 for my PCI-6704 it notifies me that my device has failed the self-test, but will proceed to open a test panel. I also have an MIO card in my system which give the same error as well. I don't notice any other odd behavior though and both seem URL: http://digital.ni.com/public.nsf/allkb/3E5773BC3F429EC886256F0A006FFCF0

Why am I Receiving Error -10401 When Outputting a Voltage in a Test Panel with my AT-AO-6/10 Board? I have an AT-AO-6/10 board installed on my computer. It shows up in both MAX and device manager. When I run a test panel in MAX, however, I receive a -10401 error. Why is this? URL: http://digital.ni.com/public.nsf/allkb/AE786749D6E63C0286256E8E0023946E

Error 10800 and Output Regeneration with the DAQCard-6715 The DAQCard-6715 is only generating output with data from the first buffer that was written to the card. When new data is written to the buffer to be output, it is ignored. Also, the Continuous Output.vi example reports error 10800 when probing the error cluster, but the VI does not stop. Why is URL: http://digital.ni.com/public.nsf/allkb/8DAA25834904A45186256C910070F7A8

PCI-6711보드를 사용할 때, 왜 -10608 에러가 발생하나요? PCI-6711을 이용하여 두개 버퍼를 이용한 파형출력(double-buffered waveform generation)을 하려고 할 때, 데이터의 전송이 이루어지지 않는다는 -10608 에러가 나타납니다. 왜 그런가요? URL: http://digital.ni.com/public.nsf/allkb/A3A840043934867286256FD60008B0CD

Why Do I Receive the Error -10608 When Using the PCI-6711? While doing double-buffered waveform generation using the PCI-6711, I get the error -10608 saying that no transfer is in progress. Why? URL: http://digital.ni.com/public.nsf/allkb/37752A79EB6A950886256C8B006E8870