Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

¿Por qué Recibo Error 88705? Intento configurar una tarjeta DAQ PCI en MAX. El dispositivo aparece correctamente bajo Device and Interfaces » NI-DAQmx Devices pero cuando realizo un "self test" o "reset device" recibo el siguiente mensaje "Error 88705". ¿Cómo puedo resolver esto? URL: http://digital.ni.com/public.nsf/allkb/024694E1E0E1C9B78625732400474F69

為什麼我會收到錯誤訊息 88705? 我試著在 MAX 裡設定我的 PCI DAQ 模組。這個裝置在 Device and Interfaces » NI-DAQmx Devices 下顯示正常。 但是我執行 "self test" 或 "reset device" 的動作時，我得到 "Error 88705"。請問我要怎麼解決這個問題呢? URL: http://digital.ni.com/public.nsf/allkb/9347770B56306E8F8625731700390271

Accessing BNC-2096 in MAX Faults After Deleting SCC Connector Block or CDAQ Chassis/Module When I do one of the following, MAX crashes or freezes forcing me to use task manager to end the process: Configure an SCC connector block with a module and a BNC-2096. Configure the BNC-2096 to reference a physical channel on the SCC module. Next, delete the SCC connector URL: http://digital.ni.com/public.nsf/allkb/4C2DAF28902CBD3486257280000DD6DC

DAQmx Error Code -89130: Device is not Available for Routing I am unable to access my multifunction DAQ board when using DAQmx. When I try to acquire data, I always receive the following error message: Error -89130: Device is not Available for Routing. What should I do? URL: http://digital.ni.com/public.nsf/allkb/61371556441E5FF68625730600775934

当我把USB-6008 或 USB-6009连到电脑时，发生错误200170 当我把USB-6008 或 USB-6009连到电脑并试图运行 Measurement and Automation Explorer中的Test Panels，我运到错误 200170 'Not able to find physical channel'。 URL: http://digital.ni.com/public.nsf/allkb/E1D59DD2EA635EFC4825725F00376DE9

被扫描的通道上发现了同样的信号，尤其当没有信号接入的时候 当扫描多个通道时，我扫描了一些未连接信号的通道。我注意到我常常从这些通道读到与先前通道同样的信号。为什么会出现这样的情况呢？为什么我从未连接信号的通道上读到的电压不是0V？为什么这个电压会改变？ URL: http://digital.ni.com/public.nsf/allkb/6156370427A86B40482572500006C226

为什么我收到 -200609 或者 -200802 的错误？ 当尝试创建一个模拟输出的任务时，任务启动前在写入数据到 DAQmx Write 函数缓冲时，我收到 -200609 或者 -200802 的错误。 URL: http://digital.ni.com/public.nsf/allkb/1CF156D3DE7A05D548257221000BE62D

Error 200170 Occurs When I Connect USB-6008 or USB-6009 to My Computer. When I plug in a USB-6008, USB-6009, or USB-6501 into my computer and try to run Test Panels for the device in Measurement & Automation Explorer, I get the following error: Error -200170 occurred at an unidentified location Possible URL: http://digital.ni.com/public.nsf/allkb/9F61B1CE00D6CE7586257204006B207E

USB-6008、USB-6009 をコンピュータに接続した際にエラー -200170 が発生します USB-6008、またはUSB-6009 をコンピュータに接続し、Measurement and Automation Explorer のテストパネルを開始しようとするとエラー -200170 「指定した物理チャンネルはこのデバイスにありません。」が発生します。 URL: http://digital.ni.com/public.nsf/allkb/C11CB62277C13857862572D40023587E

Performing a Self-Calibration on a NI 6143 Does Not Work Immediately After a Device Reset I have a NI 6143 which I just purchased from National Instruments and when I ran it through Calibration Executive to verify the performance, it failed the 'Verify Only' step. Why did this happen? URL: http://digital.ni.com/public.nsf/allkb/62D7C8D56A53B60D862572020048A0CF