PC Card (PCMCIA) Devices Can Exhibit Interrupt Failures on Windows 2000 and XP
When using a PCMCIA card on my Windows machine, I've noticed that there is a performance decrease in a CardBus-enabled PCMCIA slot or I am getting error: DAQCard not responding to first IRQ level. What does this
URL: http://digital.ni.com/public.nsf/allkb/14DFB1A1788D1F3286256E4D007CA783
|
Warning Error 0x8526 with VXI System
I have a GPIB-VXI/C controlling a VXI chassis. In the Resource Manager (Resman) output, I receive the following: WARNING !! Error Code = 0x8526 Device at logical address 224 is a PI device but did not respond to the word serial command read interrupters. This is a violation of the
URL: http://digital.ni.com/public.nsf/allkb/9A31530A82A4995B86256E36006E263B
|
I Can't Run the NI 488.2 Troubleshooting Wizard Without Failure Unless I am an Administrator
I do not have administrator access on my computer. When I try to run the NI 488.2 Troubleshooting Wizard, it fails on the last step. What is wrong?
URL: http://digital.ni.com/public.nsf/allkb/265E740C9541FF6986256D890080446F
|
PCI or PCMCIA GPIB Device Fails the GPIB Interfaces Sequentially Verified Test
When I run the Troubleshooting Wizard in Measurement & Automation Explorer (MAX), my National Instruments PCI-GPIB or PCMCIA-GPIB device fails the "GPIB Interfaces Sequentially Verified" test. How do I resolve this issue?
URL: http://digital.ni.com/public.nsf/allkb/73FC6C30625F3AB986256D3600740BC5
|
GPIB-ENET/100 Fails 'ibtsta' on Solaris 8
My GPIB ENET-100 fails the ibtsta verification test with an error of ENEB. I can see my GPIB-ENET/100 in the Ethernet Configuration Utility and I can "ping" it successfully. Why does the ibtsta test fail?
URL: http://digital.ni.com/public.nsf/allkb/C1221E8E3B12204B86256CC700713F70
|
'Access Denied' Message During USB Device Installation
I am trying to install my USB controller on my Windows 2000/XP machine. After I install the driver (NI-488.2, NI-DAQmx, etc.), I reboot the PC, and after it powers up, I plug in my USB device in the USB port. The Found New Hardware messages pops up, and after the initialization message, I
URL: http://digital.ni.com/public.nsf/allkb/1D52B53149DD637686256CAA00565E47
|
Why Do I Get 'Scan For Instruments Found Too Many Instruments' Error From MAX?
Why do I get 'Scan For Instruments Found Too Many Instruments' error from MAX (Measurement & Automation Explorer) when scanning for instruments using a '*idn?' command?
URL: http://digital.ni.com/public.nsf/allkb/53A9C26EEBF8329586256C9800614B6F
|
Receiving Error 'Cannot Find Digital Certificate' or 'Form specified by the subject is not supported or known by the specified trust provider' when installing a PCI-GPIB Board
I am receiving the error 'Cannot Find Digital Certificate' or 'Form specified by the subject is not supported or known by the specified trust provider' when installing my PCI-GPIB board on a Windows 2000 computer. I have installed my driver correctly and this only happens when the hardware wizard
URL: http://digital.ni.com/public.nsf/allkb/E65ECC6B1184673386256C7D00721A3B
|
GPIB Timeout Error on Every Other Command Set
I am writing to and reading from a GPIB instrument, and every other command set returns a timeout error. For example, I can write once and then read once, but then when I try to write and read again, my program reports a timeout error.
URL: http://digital.ni.com/public.nsf/allkb/24DC3A2F3E0F39C686256BF40066138C
|
コマンドセットを一度送信し、もう一度送信するとタイムアウトエラーが発生します
GPIBで書き込みと読み込みを行っています。一度目は正常に動作しますが、もう一度同じコマンドセットを送るとタイムアウトエラーが発生します。
URL: http://digital.ni.com/public.nsf/allkb/7E0CFA0F208F93C586256F78001A5CEB
|
