Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Preventing 'AutoConnect to First Failed' Error When Communicating with VXI Technologies SMIP Modules I am using a National Instruments VXI Controller with NI-VXI driver version 3.1 or later to communicate with VXI Technology SMIP Modules. However, when I run the Soft Front Panel on my SMIP Soft Front Panel program, I receive the error AutoConnect To First Failed. How do I correct this URL: http://digital.ni.com/public.nsf/allkb/0338AE920D9472CA86256B90006B1A7B

MXI-3 and MXI-4 Blue Screen Errors on Windows XP If I connect a PC with Windows XP to a PXI chassis with only a MXI-3 or MXI-4 card in it and no devices, Windows XP gives me the 'Blue Screen of Death' on boot up. How do I prevent this? URL: http://digital.ni.com/public.nsf/allkb/9F2D5DB451E8E64186256AC7005C8F66

'Device is not responding to the First DMA Channel' Error with VXI-MIO Board I receive the error 'Device is not responding to the First DMA Channel' when I try to Test Resources in the Measurement and Automation Explorer (MAX) for my VXI-MIO-64XE-10 or VXI-MIO-64E-1. What is going on? URL: http://digital.ni.com/public.nsf/allkb/925D3D2924BE1663862569EA005760B8

PCI-MXI-2 Is Not Recognized under Windows NT: 'EEPROM config error' I have a PCI-MXI-2 that is not recognized under a new installation of Windows NT. The PCI-MXI-2 is assigned resources and the VXI drivers (vvxid, vpcid and vnugtd) are all started and automatic, but when I open the Test & Measurement (TM) Explorer, there is an 'EEPROM config error'. When I try to URL: http://digital.ni.com/public.nsf/allkb/8019AC4DE35AE68886256969006832D9

What Do I Do if I Receive a Memory Parity Error, Followed by a General Protection Fault? What do I do if I receive a memory parity error, followed by a General Protection Fault? URL: http://digital.ni.com/public.nsf/allkb/9AFB4F57FD2CEBCB862569450050122A

Why does the SYSFAIL LED come on when the VXIbus timeout is changed in the VXI/VME Configuration Editor? Why does the SYSFAIL LED come on when the VXIbus timeout is changed in the VXI/VME Configuration Editor? URL: http://digital.ni.com/public.nsf/allkb/4ECD3AB333273DC586256E8E00238ADB

GPIB-1014 사용 후에 하드웨어 진단의 테스트 2 에서 테스트가 실패합니다. 왜 GPIB-1014 사용 후에 하드웨어 진단의 테스트 2 에서 테스트가 실패합니까? URL: http://digital.ni.com/public.nsf/allkb/6ABC43621CBA8FB28625720A000AEDB8

Test 2 of Hardware Diagnostics Fails After Using GPIB-1014 Why does Test 2 of the hardware diagnostics fails after the 1014 has been used? URL: http://digital.ni.com/public.nsf/allkb/C88BFDCF90D30971862564FB004773F0

SETUPLDR: COULDN'T OPEN DRIVE MULTI(0)DISK(0)FDISK(0) error message Windows NT installation, whether booting from a WinNT boot disk or potentially installing from a network,may exhibit the following error message on a VXIpc-850 and VXIpc-745.SETUPLDR: COULDN'T OPEN DRIVE MULTI(0)DISK(0)FDISK(0).This problem shows up when you upgrade an 850 to NT4.0. URL: http://digital.ni.com/public.nsf/allkb/195E0E15D71D8F0786256E8E00231998

Exiting Visual Basic 3.0 with NI-VXI Causes a Fatal Exception Error When I press the stop button in my Visual Basic 3.0 (16-bit) application it causes a fatal exception error. URL: http://digital.ni.com/public.nsf/allkb/DB869C8EE0FE2C698625634700788461