Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Why do I get 'IMAQBoot.exe - Entry Point Not Found' error when I restart computer? I have installed NI-IMAQ but I get this error everytime I restart my computer, how can I get rid of this? URL: http://digital.ni.com/public.nsf/allkb/BFFE6F5E691190FA8625743B003CC0F8

Error -88716 When Using A NI-DAQmx Device in LabVIEW Real-time With NI-DAQmx 8.7.1 When I try to self-test or use a DAQ device installed in a LabVIEW Real-time system with NI-DAQmx 8.7.1 I get the following error message:Error -88716 occurred at Test PanelPossible Reason(s):The requested operation URL: http://digital.ni.com/public.nsf/allkb/A47734CC1E03922186257435004D0C49

LabVIEW Real-timeとNI-DAQmx 8.7.1の環境でNI-DAQmxデバイスを使用するとエラー-88716が発生します NI-DAQmx 8.7.1がインストールされたLabVIEW Real-timeの環境で、DAQデバイスのセルフテストまたはテストパネルを実行すると以下のエラーが発生します。エラー-88716がテストパネルで発生しました推定理由:インストールされたドライバの URL: http://digital.ni.com/public.nsf/allkb/90EFBBBD1F60F8C78625745C0033A698

錯誤代碼 -88716, 當在LabVIEW Real-time系統下使用NI-DAQmx裝置以及NI-DAQmx 8.7.1 當我嘗試執行self-test或是使用安裝在LabVIEW Real-time下的DAQ裝置與NI-DAQmx 8.7.1時,我得到下面的錯誤訊息: Error -88716 occurred at Test PanelPossible Reason(s):The requested operation failed because the versions of a driver installed on the local a URL: http://digital.ni.com/public.nsf/allkb/713579014D90102C8625748300162CC9

Why Do I Get A Timeout Error When Writing Relay Counts to My Switch Module? When I try to write relay counts to my switch module through the soft front panel by going to File » Relay Maintenance » check Edit Count » Change the New Relay Count, I get a time out error. This might happen if a switch was sent in for repair and it was URL: http://digital.ni.com/public.nsf/allkb/615E442B7AD15F9F8625742D0076A586

¿Por Qué Obtengo un Error de Fin de Tiempo Cuando Conecto Contadores de Relevo a Mi Modulo de Interruptores? Cuando trato de de escribir contadores de relevo a mi modulo de interruptores mediante el front panel dentro de URL: http://digital.ni.com/public.nsf/allkb/7C5FB23347D0A2E386257462000163D6

Error -63001 NI-RIO FPGA Communications Occurs With DMA Transfers From Host to FPGA I am trying to do a DMA transfer from the 900x cRIO RT controller to the cRIO FPGA. The FPGA code compiles. However, when I run the code I get a Real-Time error saying the following: Error -63001: NI-RIO FPGA Communications.Framework: (Hex URL: http://digital.ni.com/public.nsf/allkb/257AF49E2110630F8625741F0062D292

Time-Out Error with GigE Vision Camera Why do I get a time-out error when trying to do a snap or grab with my GigE Vision camera? URL: http://digital.ni.com/public.nsf/allkb/17A956942535A2C786257419007778FF

Error 50150 - Reboot USB 9162 after upgrading to DAQmx 8.7 Immediately following an upgrade to DAQmx 8.7 and using a USB-9162, a user may see error 50150 when attempting to use the device until they restart Measurement and Automation Explorer (MAX) or reboot. The Found New Hardware Wizard may also prompt you to reboot. USB-9162 devices should not URL: http://digital.ni.com/public.nsf/allkb/D046874B01378D42862574170072561E

Measurement Studio Compatibility with the Data Execution Prevention (DEP) Setting on Windows Vista Are there any issues associated with Measurement Studio support for Visual Studio 2008 and the Data Execution Prevention (DEP) Setting on Windows Vista? URL: http://digital.ni.com/public.nsf/allkb/94C800ADF9291B798625740B00727DFF