Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Why do I get 'IMAQBoot.exe - Entry Point Not Found' error when I restart computer? I have installed NI-IMAQ but I get this error everytime I restart my computer, how can I get rid of this? URL: http://digital.ni.com/public.nsf/allkb/BFFE6F5E691190FA8625743B003CC0F8

Error -88716 When Using A NI-DAQmx Device in LabVIEW Real-time With NI-DAQmx 8.7.1 When I try to self-test or use a DAQ device installed in a LabVIEW Real-time system with NI-DAQmx 8.7.1 I get the following error message:Error -88716 occurred at Test PanelPossible Reason(s):The requested operation URL: http://digital.ni.com/public.nsf/allkb/A47734CC1E03922186257435004D0C49

Why Do I Get A Timeout Error When Writing Relay Counts to My Switch Module? When I try to write relay counts to my switch module through the soft front panel by going to File » Relay Maintenance » check Edit Count » Change the New Relay Count, I get a time out error. This might happen if a switch was sent in for repair and it was URL: http://digital.ni.com/public.nsf/allkb/615E442B7AD15F9F8625742D0076A586

Error -63001 NI-RIO FPGA Communications Occurs With DMA Transfers From Host to FPGA I am trying to do a DMA transfer from the 900x cRIO RT controller to the cRIO FPGA. The FPGA code compiles. However, when I run the code I get a Real-Time error saying the following: Error -63001: NI-RIO FPGA Communications.Framework: (Hex URL: http://digital.ni.com/public.nsf/allkb/257AF49E2110630F8625741F0062D292

Time-Out Error with GigE Vision Camera Why do I get a time-out error when trying to do a snap or grab with my GigE Vision camera? URL: http://digital.ni.com/public.nsf/allkb/17A956942535A2C786257419007778FF

Error 50150 - Reboot USB 9162 after upgrading to DAQmx 8.7 Immediately following an upgrade to DAQmx 8.7 and using a USB-9162, a user may see error 50150 when attempting to use the device until they restart Measurement and Automation Explorer (MAX) or reboot. The Found New Hardware Wizard may also prompt you to reboot. USB-9162 devices should not URL: http://digital.ni.com/public.nsf/allkb/D046874B01378D42862574170072561E

Why Do I Receive DAQmx Error -200718 When I Externally Calibrate the NI 446x with DAQmx 8.7.1? I am using NI-DAQmx 8.7 or 8.7.1. When I try to self-calibrate my NI 446x device from MAX, it calibrates successfully. When I try to externally calibrate the board manually or with Calibration Executive, I receive Error -200718 occurred at DAQmx Adjust DSA AI Calibration.vi. URL: http://digital.ni.com/public.nsf/allkb/40DB974EAD98BECA86257408005909E5

The NI PXI-5600 RF Downconverter Does Not Show up in Measurement and Automation Explorer (MAX) on the Real-Time (RT) Target When Using NI-DAQ 8.7. If a customer installs NI-DAQ 8.7 and then NI-RFSA 2.0.7, RT support for the NI PXI-5600 won't work (i.e. the NI PXI-5600 will not be recognized as a device) without an additional step. URL: http://digital.ni.com/public.nsf/allkb/E80066EB8F5BEBC586257402008303F0

Programmatically Clearing a CAN or DNET Device My program has crashed or aborted and my NI-CAN or NI-DNET object was not closed properly, when I try to restart my code again I get error -1074388986. URL: http://digital.ni.com/public.nsf/allkb/E79DD867896CABDA862573F50001D994

Error: 1074135024 Invalid value for parameter or property Error number 1074135024 is received when the property node: Fetch Relative to is set to Read Pointer and you are trying to do a Fecth/Read Measurement. A common case is when a customer is trying to integrate a URL: http://digital.ni.com/public.nsf/allkb/ECA713E12889FCA4862573F3007C75E4