Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

How Do I Control the SCC-RLY01 with My DAQ Board? I have an SC-2345 carrier with a SCC-RLY01 installed in one of the DIO slots. How do I open and close the relay? URL: http://digital.ni.com/public.nsf/allkb/54267CD3C238301D862570380076AAB8

Voltage Level on SCC-SGxx Excitation Source Drops when a Second Strain Gage is Attached When I attach a second strain gage to the SCC-SGxx module, the excitation source drops in voltage. What can I do? URL: http://digital.ni.com/public.nsf/allkb/DAD885075F6C63C286256FFF00430471

How to Connect Signals to the SCC-FT01 ? In SCC-FT01 documentation, you can not find which screws are used for counter singals. URL: http://digital.ni.com/public.nsf/allkb/33956269663E065B86256FEB005194CD

I Am Not Getting Any Frequency Readings When Using the SCC-FV01. I am trying to use the SCC-FV01 to measure a frequency signal that goes anywhere from 0 to 10 Volts. When I test it in MAX, it doesn't seem to be working. URL: http://digital.ni.com/public.nsf/allkb/D52F25097F164E4C86256FCD006027C9

How Do the Module Slots on the SC-2345 Map to the Channels on the DAQ Cards? Whenever I configure my SC-2345 and add the SCC modules to the slots, the channel number that appears right next to the module doesn't match to the channel numbers appearing when configuring a Task for them. What are all these channel numbers and why are they different? URL: http://digital.ni.com/public.nsf/allkb/1D49E47CB61CE52486256F95001A740A

Using the SCC-SG11 Shunt Calibration Module When I create a strain type global channel in MAX using a SCC-Series strain gage module, there's no option to perform calibration. How can I use the SCC-SG11 module to calibrate the SCC-SG0X or SCC-SG24 strain gage module? URL: http://digital.ni.com/public.nsf/allkb/C77748880274A56686256F89007A4E3E

How Do I Program a DAQmx TEDS Task in LabVIEW? I know how to set up DAQmx tasks and global channels in Measurement and Automation Explorer (MAX) to use my TEDS-enabled sensors, but I want to do it programmatically in LabVIEW. Is there any way to set-up my TEDS DAQmx channels directly in LabVIEW? URL: http://digital.ni.com/public.nsf/allkb/CE93FAB3AA03809686256F7A004AB8B0

Using 32 Channels Of An M-Series Card With SC-2345 I would like to use all 32 channels of my M-Series card with two SC-2345s. Is that possible? URL: http://digital.ni.com/public.nsf/allkb/AA05978D645C968886256F530075C481

Why Is the Test Panel for the SCC-FT01 Grayed Out in Measurement and Automation Explorer? I have an SC 2345 connected to a PCI-6023E card and I am trying to read data from a flowmeter through an SCC-FT01 module connected to channel J1. I went to Measurement and Automation Explorer (MAX) to test this SCC-FT01 module, but when I click on the channel with this module the Test Panels URL: http://digital.ni.com/public.nsf/allkb/48AC78CFF157E6A886256F4A006A0E79

Why Am I Getting Noisy Measurements with My SC-2345 Signal Conditioning Modules? I have an SC-2345 box with one or more signal conditioning modules. I am able to read from the modules, but I get inconsistent or noisy readings. Shouldn't the signal conditioning take care of the noise for me? URL: http://digital.ni.com/public.nsf/allkb/4F00A0167643CC2F86256F39004EDD06