Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Connecting a Digital Signal to the SC-2345 (X) on the E Series DAQ device. Plug the SCC-DO01 into any digital input/output (P0.X) socket J(X+9), where X is 0 to 7, on the SC-2345. Software: Configure SC-2345 in MAX as explained on page 22 of the SCC Quick Start Guide. 3. URL: http://digital.ni.com/public.nsf/allkb/4D57D9239DF5B312862570D10067B887

Configuring the SCC-CTR01 in MAX I am trying to add the SCC-CTR01 to my SC-2345 carrier in Measurement and Automation Explorer (MAX) but it does not show up in the drop down list. How can I configure and use this module? URL: http://digital.ni.com/public.nsf/allkb/D5D79775744D2EDE8625708A007BCD05

What do the Color Strips on SCC Modules Indicate? SCC modules have color-coded strips on their labels. What do these colors indicate? URL: http://digital.ni.com/public.nsf/allkb/886FABB22CEBF56A86257083007BC34A

Can I Use the SCC-CTR01 Module With Quadrature Encoders and Up/Down Event Counting? I have an SCC-CTR01 isolated counter module. What are the limitations of using this module with M Series and E Series devices? URL: http://digital.ni.com/public.nsf/allkb/86EBA05BC4D586AD86257082007C5744

Why is the Stripe on my SCC-CTR01 Module Blue Instead of Yellow as the Documentation Indicates it Should Be? My SCC-CTR01 module has a blue stripe on the label which seems to indicate it is compatible with analog input slots in my SCC carrier. The documentation indicates that this stripe should actually be yellow to indicate its true compatibility with counter slots. Why is this? URL: http://digital.ni.com/public.nsf/allkb/3F7F820F0DC7B4A486257082008218BC

Are SCC Modules Hot-Swappable? Problem: Are SCC modules hot-swappable? Solution: No, SCC modules are not hot-swappable because this functionality was not designed into the SCC module/carrier architecture. You should refer to the SCC Quick Start Guide for specific details on setting up your SCC system. URL: http://digital.ni.com/public.nsf/allkb/AC8191FCBE58A4F38625706C007E9AD9

What National Instruments Products Can Be Used for Current Output? Current Output is not directly supported by most of National Instruments' Multifunction DAQ devices. However, if the load is known then an appropriate voltage can be used to source up to 20 mA of current from an analog output channel. URL: http://digital.ni.com/public.nsf/allkb/4017793371AC28478625706800531CBE

What National Instruments Products Support Current Input I need to measure a current, but I don't know what products National Instruments makes that will let me read a current. URL: http://digital.ni.com/public.nsf/allkb/562D370BFF887E8486257067007A5D6F

Can I Connect a Quadrature Encoder to an M Series Card Using the SCC-FT01? I am trying to connect an encoder with UP/DOWN control to my M Series card using an SCC-FT01 feedthrough module. The SCC-FT01 User Guide says that UP/DOWN controls are tied to the P0.6 and P0.7 lines for E-Series use. However, my M-Series card uses different pins. Can I use this URL: http://digital.ni.com/public.nsf/allkb/10F258E034638B17862570380063E635

How Do I Control the SCC-RLY01 with My DAQ Board? I have an SC-2345 carrier with a SCC-RLY01 installed in one of the DIO slots. How do I open and close the relay? URL: http://digital.ni.com/public.nsf/allkb/54267CD3C238301D862570380076AAB8