How Do I Connect a BNC-2110 (or BNC-2120) to an E Series Device via an SC-2056?
I would like to use a BNC-2110 (or BNC-2120) with a 100-pin E Series device that has 64 analog input (AI) channels. I have an SC-2056 connected to my device with an SH100100 cable. How do I connect a BNC-2110 or BNC-2120 to the SC-2056?
URL: http://digital.ni.com/public.nsf/allkb/A3C2F96D5749513D86256AAF006E8B91
|
Using an External Clock with the SC-2040
Problem: How do I use an external clock with the SC-2040? Solution: You can route the external clock to PFI2 to act as the STARTSCAN signal. Note that the internal STARTSCAN signal comes from PFI7. If you want to use an external clock, you cannot use PFI7 as it is reserved.
URL: http://digital.ni.com/public.nsf/allkb/EC93E3416710685C86256A77006FCB9E
|
How Do I Use 6B Series VIs in LabVIEW 6.x or Newer?
I cannot open the 6B Series VIs in LabVIEW 6.x. I received an error stating "LabVIEW Error Code 10: VI version is too old to convert to current LV version (6.0.x)". What can I do?
URL: http://digital.ni.com/public.nsf/allkb/BD70328203ABF29486256A1D0062ED74
|
Can I Use an E Series DAQ Board to Drive an SSR Relay Module?
Can I use an E Series data acquisition (DAQ) board to drive an SSR relay module?
URL: http://digital.ni.com/public.nsf/allkb/28B88568C1A77EBB86256F1C00617DEB
|
Achievable Scan Rate with SC-2040
How do I calculate the maximum scan rate that I can achieve with my SC-2040?
URL: http://digital.ni.com/public.nsf/allkb/D6B4EA75CBA41205862569EC006240E7
|
What Does the 10 kHz Bandwidth of the 5B41 Module Mean?
Problem: What Does the 10 kHz Bandwidth of the 5B41 Module Mean? Solution: Bandwidth refers to the frequency range (DC to 10 kHz in your case) of signals that are acquired without attenuation. Therefore, the 5B41 Module has a low pass filter which removes any frequencies above 10 kHz.
URL: http://digital.ni.com/public.nsf/allkb/BB505C808CD231E1862569A4005A4D17
|
Additional Resources For The 5B Series and 6B Series Made by Analog Devices
Where can I find more information on the 5B Series and 6B Series of signal conditioning modules and backplanes?
URL: http://digital.ni.com/public.nsf/allkb/940540429E402E568625699A0068CD25
|
How Do the SSR Output Modules Work?
I am trying to assemble a system involving power supplies, SSR backplanes, solenoids, strain gage transducers, thermocouples, and a counter. I am somewhat concerned about the voltages involved.
URL: http://digital.ni.com/public.nsf/allkb/E37E4CD11942C4288625693F005D0FB4
|
Why do I Receive Error -10001 with the AMUX-64T when Reading Multiple Channels in LabVIEW?
I am trying to read channels 0, 1, 2, and 3 on my AMUX-64T accessory with the channel string AM1!0,1,2,3 or AM1!0:3. I have also tried writing them in separate indices of the 'Channels' string array of my LabVIEW VI. Whenever I try any of these, I get error -10001 in LabVIEW; however,
URL: http://digital.ni.com/public.nsf/allkb/EF832CDAF87E9BF8862568A5007B2F47
|
Why Can't SSR Output Modules Be Used with Certain DAQ Devices?
A note on the SSR modules page in the National Instruments (NI) Catalog states:'The output modules (SSR-OAC-5, SSR-OAC-5A, and SSR-ODC-5) will not work with 6503 (DIO-24), 6508 (DIO-96), 1200 family, DAQCard-700, PC-LPM-16, AO-2DC family, or the extended digital I/O lines of E Series
URL: http://digital.ni.com/public.nsf/allkb/3F33283974B3692786256894006D7953
|
