Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Using SC-206X Boards with M Series DAQ Devices Using the SHC-68-68-EPM cable with an 68M-50F adaptor, connect the DAQ device to one of the two 50-pin ribbon cable connectors (J1 and J2) of the SC-2050 board. URL: http://digital.ni.com/public.nsf/allkb/9D688D259C0D796748256F7D0080FC4F

What Are Flyback Diodes and Why Are They Used? I have an output SSR module and I was told that I need to use flyback diodes to protect the system. What are these diodes and why are they used? URL: http://digital.ni.com/public.nsf/allkb/336D3653F6B6387386256F36005BE09F

Accessories in Traditional NI-DAQ and NI-DAQmx NI Home 3 ratings: 4.33 out of 5 Rate this Document Accessories in Traditional NI-DAQ and NI-DAQmx Hardware: Multifunction DAQ (MIOConnector Blocks>>BNC-2080, Multifunction DAQ (MIOConnector Blocks>>BNC-2090, Multifunction DAQ (MIOConnector Blocks>>BNC-2110, Multifunction DAQ (MIOConnector URL: http://digital.ni.com/public.nsf/allkb/B50A1CA411D90EAD86256F1E0065FDC0

Can I Use my SC-2311 with an M-Series Device? Problem: Can I use the SC-2311 with an M-series device? Solution: Yes, the SC-2311 is pin-compatible with M-series devices, and therefore can be used in DAQmx with 5B and SSR modules. You cannot add the SC-2311 as an accessory in DAQmx, but this is not a requirement for using the modules. URL: http://digital.ni.com/public.nsf/allkb/6CDB32DAFD77D4AB86256F1D004DE97F

Can I Use my SC-2311 with an M-Series Device? Problem: Can I use the SC-2311 with an M-series device? Solution: Yes, the SC-2311 is pin-compatible with M-series devices, and therefore can be used in DAQmx with 5B and SSR modules. You cannot add the SC-2311 as an accessory in DAQmx, but this is not a requirement for using the modules. URL: http://digital.ni.com/public.nsf/allkb/C022935B4593113286257116005719B6

E-Series Common Mode Voltage Limitations I am performing an analog acquisition using a National Instruments data acquisition board and it says that I can input up to 10 V differentially. Does this mean that I can connect 100 V on one lead and 110 V on another lead? URL: http://digital.ni.com/public.nsf/allkb/1A9FB36240EAB28286256F1800063138

Configuring SC-2311 in MAX Problem: How can I configure my SC-2311 in MAX? Solution: If you want to configure SC-2311 using MAX you should be able to do it under Traditional NI-DAQ Devices. 1. Right click on the device under Traditional NI-DAQ Devices and go to Properties. 2. You will have a configuration window pop up 3. URL: http://digital.ni.com/public.nsf/allkb/CD1E01FA5FF7385586256F0F0059EE56

Why Does My RLY-01 SCC Module Default to the Normally Open (NO) State? Problem: Why Does My RLY-01 SCC Module Default to the Normally Open (NO) State? Solution: The RLY-01 module is driven by the DIO lines on Multifunction DAQ boards. The state of the RLY-01 module is not guaranteed until the board's DIO lines are in output mode. URL: http://digital.ni.com/public.nsf/allkb/C9D0249BF68667EA86256ED6004F2FCC

GPIB-USB-B Grounding and Isolation I have a system setup where the PC that holds the GPIB-USB-B is grounded at a different potential than the GPIB instrument I am using. I have used PCI-GPIB in place of the GPIB-USB-B in the same PC for years without issues, but I had to send the GPIB-USB-B in for repair. Is there a problem URL: http://digital.ni.com/public.nsf/allkb/2AC7A5E028F1B09486256EB5006AB934

Remote Sense Inputs on the SCXI-1520 and PXI-4220 I noticed two input terminals on my SCXI-1314 terminal block: RS+ and RS- What are these terminals and how do I use them? URL: http://digital.ni.com/public.nsf/allkb/724FDFA5FEA4FE9586256E9000762B64