Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Timing and Programming Considerations for Onboard Motion Programming I understand that for an onboard motion application that the controller is required to provide a certain amount of time for my application. However, the program does not run deterministically. Is this expected behavior? URL: http://digital.ni.com/public.nsf/allkb/ABC7387CF365A461862572C1007CDD23

Implementing Feedforward Position Component on NI-Motion Controllers How can I implement a feedforward position component to my system if I know that my load will vary linearly as I move away from the zero position? URL: http://digital.ni.com/public.nsf/allkb/53BF23F982C3BF17862572AD00701503

Creating Custom Cables for NI Motion Controllers (733x, 734x, 735x) I do not see a cable suitable for my needs, so I would like to create my own custom cable. What are the needed connectors and who makes them? URL: http://digital.ni.com/public.nsf/allkb/569A8CC853124528862572A0005CD5E4

Conversion Factor on the NI 9505 The NI 9505 is a Servo Drive module that can be used for current loop control algorithms. These algorithms require the user to specify the Current Setpoint and Current Limit (Amps) as floating point [DBL] numbers. Because the FPGA on the NI 9505 does not currently interpret URL: http://digital.ni.com/public.nsf/allkb/0E95A86A1323EBD38625729E000BD4A1

Where Can I Find The Warranty For My NI Hardware? I'm trying to find the warranty information for my NI hardware. Where can I find it? URL: http://digital.ni.com/public.nsf/allkb/8341879DC763DF5886257289005D816E

Configuring Axis Resources for a Motion Dual-Loop Feedback System I would like to use dual encoders, but I only have two axes on my MID. Measurement & Automation Explorer (MAX) defaults dual encoding to Axis 1 and 3, but I need to figure my second feedback encoder to a different axis on my UMI. Is this possible? URL: http://digital.ni.com/public.nsf/allkb/57980429F24F87058625727D0003384F

Why is the Digital Output Line 1 on my PCI-7390 Not Working? I have a PCI-7390 motion controller and I am trying to use the digital output lines. When using line 0 on the ports related to axis 1, 2, 3 and 4, I am able to change the line state. But when I try to change the line state with line number 1, I do not get the results I am expecting. How can I URL: http://digital.ni.com/public.nsf/allkb/9264ECD5CB2BF56E8625727D00099A71

Configure and Test a Stepper Motor How do I configure my NI 73XX motion controller to control my stepper motor? URL: http://digital.ni.com/public.nsf/allkb/9675C83F037811F68625727C0002A4A5

How do I synchronize 2 NI-Motion Control Boards? Is it possible to synchronize 2 or more NI-Motion control boards? If so, how do I do it? URL: http://digital.ni.com/public.nsf/allkb/D611E9F18CF4A2018625727B004CEA09

NI 9505 Module Chassis Power LED is not Illuminated when Plugged into a Powered cRIO Chassis My cRIO chassis is powered up and working properly, but the green power LED is not on, even though the NI 9505 Operating Instructions say... 'The Power LED (green) illuminates when the NI 9505 is properly inserted into a URL: http://digital.ni.com/public.nsf/allkb/45E16F3A9F1A25508625727A007E5679