Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Where can I find the Danaher P7000AC (P70360) and P7000DC (P70530) Stepper Drive Manuals? Where can I find the Danaher P7000AC (P70360) and P7000DC (P70530) Stepper Drive Manuals? URL: http://digital.ni.com/public.nsf/allkb/FEB445A71B94412A86257345004DC76C

Ghosting on Motion Controller Analog Inputs I have an NI-73xx Motion controller and I am using the analog input to read an analog signal. I have hooked up my signal to analog input channel 3, but in my program I am reading from analog input 1. Even though I am reading from a different channel than what I have connected, I still see URL: http://digital.ni.com/public.nsf/allkb/9CDFFA9DB8A876A48625733C0012796E

Will Electronic Gearing Work with an Axis that is Performing Contour Moves? I plan to electronically gear two motion axes together, and perform contour moves with the master axis. Will this work? URL: http://digital.ni.com/public.nsf/allkb/629442FB7D32074D862573310050C955

National Instruments Motion Controller Boards & Drivers I have a National Instruments Motion Controller board but I am unsure if I should use ValueMotion, FlexMotion or NI-Motion. Which one should I use and why? URL: http://digital.ni.com/public.nsf/allkb/782E7400A9FE22A68625731C005C973A

Determining the Step Length and Control Loop Update Period for Servo Tune I have a NI 7330/7340/7350 motion controller. I am using it to control a servo motor, but I am having trouble tuning it in the Servo Tune tab in the Measurement & Automation Exploxer (MAX). In the Servo Tune's Step Response tab, what is the appropriate value for Step Length? Also, in the URL: http://digital.ni.com/public.nsf/allkb/98DE5BEB4A379A4B8625730D007258AC

A Simple Method for Servo Motor Tuning I can't seem to get my servo motor tuned. Is there a simple method to find PID gains that will be give me something close to my desired response? URL: http://digital.ni.com/public.nsf/allkb/806F6F0B775FAF32862572FA0052F2AB

Does the Number of Analog Inputs/Outputs on a Motion Controller Depend on Axes Available? I have an NI PCI-7342 motion controller and I see that there are 4 analog inputs & 4 analog outputs available on the Motion I/O connector. Do I have access to all of these analog signals or am I limited by the number of axes I have (i.e. 2 analog inputs and 2 analog outputs)? URL: http://digital.ni.com/public.nsf/allkb/B513A7284A2D3F4C862572E50007ACB1

Tuning a Motion Controller for Different Dynamics Forward and Backward I have a closed-loop system that is driven by a 7340 motion controller. The load moves in the vertical direction. Due to the effects of gravity, I have different loading parameters when traveling downward opposed to traveling upward. How can I tune my motion control card to compensate for the URL: http://digital.ni.com/public.nsf/allkb/8108FBCAF15FDEE0862572DE0071AE6B

Closed Loop Stepper Movement is Inaccurate I have a closed loop system setup on my stepper motor to ensure that my movements are accurate; however, when I command the motor to move, it does not move to the appropriate location. Why is this happening? URL: http://digital.ni.com/public.nsf/allkb/E315EF739926310B862572CF00805A51

Error -70207 when Initializing a PCI-7390 Motion Controller When initializing my PCI-7390, I recive the error -70207 says 'The move cannot be completed because the inhibit input of the commanded axis is active.' Why am I getting this error, and what can I do to initialize the board without getting this error? URL: http://digital.ni.com/public.nsf/allkb/E55301855F60C9DA862572C20065ECD4