Incorrect PID Update Rate Error (-70108) with NI 7340 and NI 7350 Controllers in MAX
I correctly set the PID rates in Measurement Automation Explorer (MAX) to valid values (as described in the NI 7340 and NI 7350 hardware manuals and the 'Enable Axes' VI/function help). When I try to initialize my controller from MAX, I receive error -70108
URL: http://digital.ni.com/public.nsf/allkb/C0C521CD425A253B862574400069237A
|
Why am I unable to activate my motion hardware?
I attempted to activate my motion control hardware in MAX or in the NI License Manager and was unable to do so, what do I do now?
URL: http://digital.ni.com/public.nsf/allkb/9386ED50FC5C34288625743200600C43
|
Using the Up/Down Counter of M-Series cards with the DAQ Signal Accessory
I am trying to use the quadrature encoder that is built into the DAQ Signal Accessory to complete the exercises in the Data Acquisition and Signal Conditioning
URL: http://digital.ni.com/public.nsf/allkb/B764E65F4CF03B168625741E00765951
|
Configuring the P7000 Series Stepper Drives for the Correct Motor
I have a P7000 Series Stepper Drive, and need to configure the drive for my specific motor. The sticker on the drive lists the appropriate switch settings to use for various motors, but mine is not listed. How can I configure the drive with the appropriate settings?
URL: http://digital.ni.com/public.nsf/allkb/43E49533369E4230862574130065CBF1
|
What cables do I need with my NI-Motion Hardware?
I am trying to decide which cable to buy with my NI Motion Hardware. There are multiple options available on the motion advisors website (http://sine.ni.com/nips/cds/view/p/lang/en/nid/3971). What are the differences and which
URL: http://digital.ni.com/public.nsf/allkb/5BCA4D4A31025542862573BF0057750A
|
How Do I Access the DPull Pin on My UMI-7774?
I have a NI 733x, 734x, or 735x Motion Controller connected the the UMI-7774, and I need to change the default power-up state. I know that I need to either connect the DPull pin to ground or to 5V, depending on the state that I want to set, but I do not see any way to access that pin from
URL: http://digital.ni.com/public.nsf/allkb/DFD48E6863AD245A86257378007F1708
|
How Can I Specify Acceleration, Velocity, and Deceleration for a Contoured Move?
How can I specify acceleration, velocity, and deceleration profiles for a contoured move when the trajectory generator on the motion controller is not used during a contoured move?
URL: http://digital.ni.com/public.nsf/allkb/F58339DBA74CF728862573760005B0B1
|
How Can I Trigger an Event Off of an Encoder Line (A, B, or Z)?
I would like to trigger an event on my 733x, 734x, or 735x motion controller card based off of an encoder line (A, B, or Z). How can I do this?
URL: http://digital.ni.com/public.nsf/allkb/70BF642F99126FC38625736F0056D7AB
|
Where can I find the Danaher P7000AC (P70360) and P7000DC (P70530) Stepper Drive Manuals?
Where can I find the Danaher P7000AC (P70360) and P7000DC (P70530) Stepper Drive Manuals?
URL: http://digital.ni.com/public.nsf/allkb/FEB445A71B94412A86257345004DC76C
|
Ghosting on Motion Controller Analog Inputs
I have an NI-73xx Motion controller and I am using the analog input to read an analog signal. I have hooked up my signal to analog input channel 3, but in my program I am reading from analog input 1. Even though I am reading from a different channel than what I have connected, I still see
URL: http://digital.ni.com/public.nsf/allkb/9CDFFA9DB8A876A48625733C0012796E
|
