Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Calibration Executive Report Shows Failure for NI 4060 when Software Indicates Passing When I run a "verify only" on a 4060 it will show as a green PASS but in the report, it does not meet the "as Left" data (which are 24hr specifications) and thus will show FAILED. URL: http://digital.ni.com/public.nsf/allkb/F099D251EAFA73DE862573AE000A6F1C

Replacing an Older DMM With a Newer One Results in 'Device Not Recognized' Error in Text-Based Program I replaced my PXI-4060 with the newer PXI-4065 and ran my C, CVI, or Visual Basic code. I get the error message Device not recognized. Why is this error occuring and how can I fix it? URL: http://digital.ni.com/public.nsf/allkb/A99056ACBAC7C64E8625739A00511727

NI-DAQmx Error -50103 When Performing AI and AO With the NI-4461 When I use the Multi-Device Sync-AI and AO-Shared Timebase & Trig-DSA shipping example or when I try to synchronize Analog Output (AO) and Analog Input (AI) on my NI 4461 Dynamic Signal Analyzer (DSA) card I receive the following error: URL: http://digital.ni.com/public.nsf/allkb/8C7A7AF1A6DDD00086257399005B8513

How to Configure the Vertical Range Per Channel of My National Instruments Digitizer? I have an NI-SCOPE device and would like to adjust the Channel 0 vertical range independently of the Channel 1 vertical range. I have tried using the niScope Configure Vertical VI but it changes the settings for both channels. How can I change the vertical ranges independently? URL: http://digital.ni.com/public.nsf/allkb/DD92BCF134C342C48625738B0065306C

NI 4498 Connector Diagram and Pinout I'm having difficulty locating the NI 4498 connector diagram with the accompanying pinout. Where can I find this? URL: http://digital.ni.com/public.nsf/allkb/0E96DC4546D1D092862573830072B519

Error-50251 When Performing Self-Calibration on My NI-5922 After Upgrading from NI-SCOPE 3.3.2 to NI-SCOPE 3.4 Previously I had NI-SCOPE 3.3.2, which I had installed from the August 2007 device driver CDs. I recently upgraded my NI-SCOPE driver to version 3.4 and now I cannot self-calibrate my NI-5922. In Measurement and Automation Explorer the self-calibrate option is disabled and I do not see any URL: http://digital.ni.com/public.nsf/allkb/B84AE4281BA524508625737C005375AF

Sample Rate Adjustments Do Not Affect LC Measurements of a DMM I have tried adjusting the sample rate of an inductance or capacitance (LC) measurement using the NI-DMM driver. However, the changes have no effect on my actual measurement speed. URL: http://digital.ni.com/public.nsf/allkb/E03C3837A9EEEF3D8625736B00216501

Removing the Plastic Guide from Longer PCI Cards The plastic guide on the back of the longer PCI cards makes the device too long to fit in my PC, can I unscrew this guide and remove it, or will this affect my card's performance? URL: http://digital.ni.com/public.nsf/allkb/B2D9FCF6B99C153B86257356005E5587

Self-Resetting Fuse Additional Information National Instruments has learned of customers experiencing damaged modules and damage to chassis or adjacent modules due to improper connections. This document provides URL: http://digital.ni.com/public.nsf/allkb/E48B7DDC4EA9DE0886257333005C28FE

What is the AUX input used for on NI-DMM Modules? I am looking into purchasing a National Instruments DMM Module and I would like to know what the AUX connector actually does. Do I need it? URL: http://digital.ni.com/public.nsf/allkb/A1EC1EBFBF8226F68625732B00384372