Category(s) Selected [start over]

KnowledgeBase [see results below]. To refine your results, select another category.

Synchronization Frequency for PXI-6682 and PCI-1588 Implementing PTP Both the PXI-6682 and PCI-1588 support PTP (Precision Time Protocol) but they each have a different synchronization frequency. Why is there such a large difference in the accuracy and what is this accuracy measurement dependent on? URL: http://digital.ni.com/public.nsf/allkb/846CDBA8A291526E862573F0001A636E

Different Types of Isolation: Channel-to-Channel, Bank (Channel-to-Bus), and Channel-to-Earth Ground Isolation What are the differences between the types of electrical isolation NI offers on devices? I do not understand the differences between channel-to-channel, bank (channel-to-bus), and channel-to-earth ground isolation. URL: http://digital.ni.com/public.nsf/allkb/CF71091043A6193B862573D70077138B

Configuring the NI MES-3980 IP Address and Accessing the Web Console I need to configure the NI MES-3980 for a static or dynamic IP address and then access the web browser to configure settings. How can I get this accomplished? URL: http://digital.ni.com/public.nsf/allkb/5983CCB59977B3DC862573D0006156D6

USB 232/4 Device Shuts Down My USB 232/4 device works for a while and suddenly turns off and then back on after a couple of minutes. I have already checked the USB power settings in Device Manager to disable allowing to turn off device for power savings. I also verified that only one device is connected to one USB root URL: http://digital.ni.com/public.nsf/allkb/9D3890BE49FF5D43862573A7006E5612

I Can't See My FTDI - FT2232C USB Device in MAX? I am trying to communicate to my USB FT2232C device using LabVIEW. I can see it in Device Manager but cannot see it in MAX. URL: http://digital.ni.com/public.nsf/allkb/8D86BCD37B16697D8625739C0037A933

Why Am I Unable to Configure LeCroy Digital Storage Oscilloscopes to Be Used With NI-VISA? I have a LeCroy Waverunner 6100 Oscilloscope and I'm trying to configure it to be used with NI-VISA through TCP/IP. I have already set the IP address and subnet settings for both my host PC and the oscilloscope. However, when I try to create a new VISA TCP/IP resource in MAX I am unable to URL: http://digital.ni.com/public.nsf/allkb/FCC6E8CB7F3EEA5186257376003669BE

Receiving Error when accessing properties of a Serial Device through a USB Serial Adapter I’m using a third party serial device via a third party USB Serial adapter. I am able to configure and communicate with it under hyper-terminal. When testing the device in MAX, I am unable to change items such as the Baud Rate and Parity Bits. The error I receive is 0xBFFF0072. URL: http://digital.ni.com/public.nsf/allkb/D42EB343B549A27A8625734400574D8A

Lost UDP Packets at Fast Transfer Rates When the UDP packets come in at high data rates (greater then 2Mb/s), they start getting lost, especially when the CPU gets loaded by other tasks. URL: http://digital.ni.com/public.nsf/allkb/D5AC7E8AE545322D8625730100604F2D

Why Does My GPIB-USB-HS Device Prompt the Add Hardware Wizard Each Time I Plug it in? Every time I unplug my GPIB-USB-HS device and plug it back in, the Add Hardware Wizard pops up and re-installs the drivers. Each time this happens I lose all of the device configuration settings. How can I avoid this? URL: http://digital.ni.com/public.nsf/allkb/13B27DA885E3F3D2862572CA0065FF70

Where Can I Find The Warranty For My NI Hardware? I'm trying to find the warranty information for my NI hardware. Where can I find it? URL: http://digital.ni.com/public.nsf/allkb/8341879DC763DF5886257289005D816E